Enviro M55-FPIs640 Owner'S Manual Download Page 18

Installation

c

LeaRances

 

to

 c

ombustibLes

:

Figure 4: M55C-FPI Clearance to Combustibles. 

t

HeRmostat

 i

nstaLLation

:

1. Install the wall thermostat (millivolt rated thermostat 

recommended, or a 12/24 Volt rated thermostat set to 

millivolts) in a location that is not too close to the unit 

but will effectively heat the desired area.

2.  Connect  the  Thermostat  or  Timer  to  the  thermostat 

wires on the unit. (Fig. 5)

If the heat in the room becomes too great, the high limit 

switch may turn the stove off and the switch will have to 

be manually reset. To reset the high limit switch:

-open the hopper lid

-remove plug under control panel

-use screwdriver to press down on the button on top of 

the snap disk switch

Figure 5: Thermostat connection wires.

Certified for use in Canada & USA

Certifié pour installation au 

Canada et aux Etats-Unis.

Model / Modèle: M55C-FPI
Listed Room Heater, Pelletized Fuel Type (Appareil de chauffage à granules  certifié)
Input rating when using: Wood Pellets/Corn - 55,000BTU (16.1KW*hr)  Wheat/Barley - 53,000BTU (15.5KW*hr)
(Le chauffage d'énergie avec: Boulettes de bois/lMaïs - 55,000BTU (16.1KW*hr) Blé/l'Orge - 53,000BTU (15.5KW*hr)) 
Tested to (Testée selon): ASTM 1509-04.  US Environmental Protection Agency, certified to comply July 1, 1990, particulate 
emission standards. (États-Unis Environnemental Protection Agence, a certifié pour conformer au Juillet 1, 1990, les normes de 
particules d'émission.) 
Standard for Fireplace Inserts / Norme pour des Insertions de Cheminée: ULC S628

Install and use only in accordance with the manufacturer's installation and operating instructions. Contact local building 
or fire officials about restrictions and installation inspection in your area.  Do not connect this unit to a chimney flue 
serving  another  appliance.  Inspect  and  clean  exhaust  venting  system  frequently.  See  local  building  code  and 
manufacturer's  instructions  for  precautions  required  for  passing  a  chimney  through  a  combustible  wall  or  ceiling.  
ELECTRICAL RATING: 120 Volts, 60Hz, 4.2 Amps.  Route Cord Away From Heater.
For use with pelletized solid fuels - wood, corn, wheat, & barley only. Operate only with viewing door and ash removal 
door closed. Only replace glass with ceramic glass. Components  required  for  installation:    listed  4inch  (100  mm) 
stainless steel chimney liner.  
Installez et utilisez cet appareil seulement selon les instructions d'installation et d'opération du fabricant. Contactez les 
autorités locales de votre quartier concernant les restrictions et les inspections d'installation. Inspectez et nettoyez le 
système d'échappement fréquemment. Consultez les codes de bâtiment locaux et les instructions du fabricant pour les 
précautions  à  prendre  lorsque  une  cheminée  doit  être  installée  au  travers  un  mur  ou  un  plafond  combustible. 
CLASSEMENT ÉLECTRIQUE : 120 Volts, 60 Hz, 4.2 Amps. Placez le câble électrique loin de la chaleur. 

MANUFACTURED BY / FABRIQUE PAR:

SHERWOOD INDUSTRIES LTD.

VICTORIA BC CANADA

DATE OF MANUFACTURE / DATE DE FABRICATION:

J     F      M     A    M    J     J     A     S     O     N     D          2010     2011     2012

CAUTION:

HOT WHILE IN OPERATION. DO 

NOT TOUCH. KEEP CHILDREN, 

CLOTHING AND FURNITURE 

AWAY.  CONTACT MAY CAUSE 

BURNS. SEE NAMEPLATE AND 

INSTRUCTIONS.

 

ATTENTION:

L'APPAREIL EST CHAUD LORSQU'IL                                                             
FONCTIONNE. NE PAS TOUCHER. GARDER LES ENFANTS, 
LES VÊTEMENTS ET LES MEUBLES ÉLOIGNÉS DE 
L'APPAREIL EN MARCHE. UN CONTACT AVEC CELUI-CI 
POURRAIT RÉSULTER EN DES BRÛLURES. VEUILLEZ 
VOIR LA PLAQUE DU FABRICANT ET LES INSTRUCTIONS.

DO NOT REMOVE THIS LABEL / NE RETIREZ PAS CETTE ÉTIQUETTE

C-12224

WH-M55C-FPI

Serial No. / No. De Serié:

To Start Stove: Select fuel type mode; PREMIUM PELLETS for superior quality pellet fuel, REGULAR PELLETS for all 
grades of wood pellets & MULTIFUEL for all other fuels. Press the ON / OFF button. For first time use, a small handful 
of pellets in the burn pot liner will speed up ignition.
To Operate Stove: MANUAL MODE: When a fire has been established the stove settings are adjustable. / HIGH/LOW 
MODE:  (Requires  a  thermostat)  When  the  thermostat  calls  for  heat  the  stove  settings  are  adjustable.    When  the 
thermostat contacts open, the HEAT LEVEL and Fans will drop down to the LOW setting until the thermostat contacts 
close  again.  /  AUTO/OFF  MODE:  (Requires  a  thermostat)  When  the  thermostat  contacts  close,  the  unit  will  light 
automatically. Once up to temperature the stove settings are adjustable. When the thermostat contacts open, the stove 
will drop down to the LOW settings for 30 minutes. If within the 30 min the thermostat contacts close, the HEAT LEVEL 
will return to previous MANUAL setting or if the thermostat contacts remain open the stove begin its shutdown routine 
and it will restart when the thermostat closes.
To Turn Off Stove: MANUAL and HI / LOW mode: Press the ON / OFF button
AUTO / OFF mode: Turn the thermostat down or off.
Pour  démarrer  le  poêle:  Choisir  le  mode  pour  le  carburant  ;  PREMIUM  PELLETS  pour  le  carburant  de  boulette  de 
qualité  de  superior,  REGULAR  PELLET  pour  tous  degrés  de  boulettes  de  bois  &  MULTIFUEL  pour  tous  autres 
carburants. Appuyer sur le bouton "ON/OFF". Pour l’usage de première fois, une petite poignée de boulettes dans le 
pot de brûlure hâtera l'allumage. 
Pour faire fonctionner le poêle :  MODE MANUEL : Lorsque le feu est bien établi, les réglages peuvent être ajustés. / 
MODE "HIGH/LOW" : (Nécessite un thermostat) Lorsque le  thermostat requière de la chaleur, les réglages peuvent 
être  ajustés.  Lorsque  les  contacts  du  thermostat  ouvrent,  le  réglage  du  niveau  de  chaleur  et  les  ventilateurs 
s'ajusteront  au  réglage  "  bas  "  jusqu'à  ce  que  les  contacts  du  thermostat  se  referment.  /  MODE  "AUTO/OFF"  : 
(Nécessite un thermostat) Lorsque les contacts du thermostat ferment, le poêle s'allumera automatiquement. Lorsque 
la température adéquate est atteinte, les réglages peuvent être ajustés. Lorsque les contacts du thermostat ouvrent, le 
poêle s'ajustera aux réglages "LOW" pendant 30 minutes. Si les contacts du thermostat sont fermés pendant ces 30 
minutes, le réglage de niveau de chaleur retournera en réglages "MANUEL" ou si les contacts du thermostat restent 
ouverts, le poêle entamera le processus d'arrêt et il vouloir redémarrer lorsque les contacts du thermostat refermer. 
Pour éteindre le poêle : MODE MANUEL ET " HIGH/LOW " : Appuyer sur le bouton "ON/OFF". 
MODE "AUTO / OFF" : Régler le thermostat à la baisse ou éteignez le.

Utilisation avec granules  - le bois, le maïs, le blé, & l'orge seulement. Utiliser seulement lorsque les 
portes avants et la porte du réceptacle de cendre sont fermées. Si une ou des vitres devaient être 
remplacées, utilisez seulement du verre céramique. Les composantes requises pour l'installation: 
une rêvetement de cheminée reprisé en acier inoxydable 4”.

16622

Sidewall to center of unit (

De la paroi au centre de l'unité) 

24” (610 mm)

Sidewall to surround panel (De la paroi à l'entoure le panneau) 

2” (51 mm)

Bottom of unit to an unshielded 12” (305 mm) mantle 

 

(Le fond de l'unité à un manteau de cheminée non blindé) 

33“ (838 mm)

Unit to top facing (protruding ¾” [19 mm]) 

 

(

De l'unité au sommet du parement)

 

0” (0 mm)

Unit to side facing (protruding ¾” [19 mm]) (

De l'unité au côté du parement)

 

0” (0 mm)

From door opening of unit to edge of floor protection 

 

(De la porte ouvrant au devant de protection de plancher) 

6” (152 mm)

From side of unit to edge of floor protection 

 

(De l'ouverture de porte pour prendre parti de protection de plancher) 

6

” (152 mm)

C

A

E

B

D

Adjacent 

 w

al

l

G

F

Combustible floors must be protected 
by a non-combustible material. 
- See Owners Manual. 
Le plancher combustible doit être 
protégé par un matériel incombustible. 
- Consultez le manual.

INSTALLED AS A FIREPLACE INSERT STOVE MODEL (FPI) / A INSTALLE 
COMME UN MODELE SUR PIED DE POELE.
Minimum clearances to combustible materials./ Les dégagements minimums aux 
matériels combustibles:



These dimensions are minimum clearances.

It  is  recommended  that  you  ensure 

sufficient  room  for  servicing,  routine 

cleaning and maintenance.

The unit must be installed with a minimum 

of 6” (152 mm) of floor  protection in front 

of and to the sides of the door opening.

18

Summary of Contents for M55-FPIs640









































Reviews: