Enviro EG28 BV Owner'S Manual Download Page 22

22

Warranty

Sherwood Industries Ltd. offers a Limited Lifetime Warranty on this gas product. This limited lifetime warranty 

covers the appliance for a period of seven years from the date of installation.  This warranty applies only to the 

original owner in the original location 
Covered under the lifetime warranty are Cabinet Sides, Tops, Pedestals, Surround Panels and Chassis and Heat 

Exchanger. These steel components are covered against manufacturer’s defects for 5 years and labor for the first 

year and for parts only thereafter.* The following exclusions apply:- over-firing due to incorrect setup or tampering,  

damage  caused  by  incorrect  installation,  usage  or  abuse.    The  unit  must  be  properly  installed  by  a  qualified 

technician or installer, and must meet all local and national gas and building code requirements.
We also cover against manufacture defects under our lifetime warranty. The following components,

Gold Plating, Log Set, Burners and Glass (*) The following exclusions apply: 

Gold plating- Damage caused by scratching, marring, chemicals, fingerprints, abrasive cleaners or discoloration with 

age or over-firing  

Glass- use of harsh or abrasive cleaners, striking the glass or surface contaminates.

Log-set- Damage caused by incorrect handling or misuse.  

Burners- damage caused by improper or continuous operation under incorrect conditions.

The paint on the Metal Brick Liner may peel. This is due to the extreme conditions applied to the paint and is no 

way covered under warranty.
* TO A MAXIMUM OF SEVEN YEARS

Sherwood Industries Ltd. offers a 2-year warranty on all the Electrical Components and Gas Components against 

manufacturing defects.  Paint is covered against flaking. This offer includes parts and labor for 1 year and for parts 

only thereafter.

Your dealer shall make all claims under this warranty in writing.

WHEN  FILING  A  WARRANTY  CLAIM  PLEASE  COMPLETE  THE  FOLLOWING  INFORMATION  ON  AN 

OFFICIAL WARRANTY CLAIM FORM:
TO THE DEALER

Name, address and telephone number of purchaser and date of purchase.
Date of installation. Name of installer and dealer. Serial number of the appliance. Nature of complaint, defects or 

malfunction, description and part numbers of any parts replaced.

TO THE DISTRIBUTOR

Sign and verify that work and information are correct.

This warranty covers defects in materials and workmanship only if the product has been installed according to the 

manual’s instructions. If the product is damaged or broken as a result of misuse or mishandling the warranty does 

not apply. The warranty does not cover removal and re-installation costs.
Sherwood Industries Ltd. reserves the right to repair or to replace the defective product. The shipping costs are to 

be paid by the consumer. All warranties by the manufacture are set forth herein and no claim shall be made against 

the manufacturer on any oral warranty or representation.
Sherwood Industries Ltd. and its employees or representatives will not assume any damages, either directly or 

indirectly caused by improper usage, operation, installation, servicing or maintenance of this appliance.

Sherwood Industries Ltd. reserves the right to make changes without notice. Please complete and mail the warranty 

registration card and have the installer fill in the installation data sheet in the back of the manual for warranty and 

future reference. 

Summary of Contents for EG28 BV
























Reviews: