manualshive.com logo in svg

Enviro E33GI, Owner'S Manual

Share
Download
Enviro E33GI Owner'S Manual Download Page 21

V

enting

:

WARNING: This appliance has been designed to draw room air for proper heat circulation 

from the sides and bottom of the unit, and out the top front.  Blocking or modifying these 

openings in any way can create hazardous situations.

The vent length for the fireplace must be between 8ft (2.44 m) and 30ft (9.14 m).
This model is vented with a 3” intake and a 3” exhaust aluminum or stainless steel flex vent leading into 

a vertical termination cap. The flue collars of this model will fit inside of a standard 3” vent and must be 

fastened directly to the vent with three screws.. The exhaust vent and air intake are both located on the 

top of the unit.
Check periodically that the vents are unrestricted. Also ensure that all direct vent pipes have been 

properly sealed and installed after routine inspection or cleaning. The air intake and exhaust pipes must 

be installed in the correct locations on the top of the fireplace.

Figure 26: Installation with a non-combustible build out.

Initial Installation

QUALIFIED INSTALLERS ONLY

Non-Combustible

Facing Material Onl

y

Surround Panel

Non-Combustible

Framin

g

i.e. steel stud

All Sides of Build Out

Sealed off

Finished Opening 

Dimensions (H x W) =

Surround Panel - Desired Overlap

Summary of Contents for E33GI










































Reviews:

No comments

Brands by name

Popular brands

Load more brands