background image

12

Initial Installation

QUALIFIED INSTALLERS ONLY

V

ERTICAL

 I

NSTALLATION

:

STEP 1.

  Check the instructions for required clearances (air spaces) to combustibles when passing through ceilings, 

walls, roofs, enclosures, attic rafters, or other nearby combustible surfaces. Do not pack air spaces with 

insulation.

C

ORNER

 I

NSTALLATIONS

:

Figure 13: Corner installation top vented.

Figure 14: Wall Framing for 10” (25.4 cm) x 10” (25.4 

cm) Hole for Vertical Installation. 

STEP 2

. Set the gas appliance in the desired location. 

Drop a plumb bob down from the ceiling to the 

position  of  the  appliance  flue  exit,  and  mark 

the location where the vent will penetrate the 

ceiling.  Drill  a  small  hole  at  this  point.  Next, 

drop  a  plumb  bob  from  the  roof  to  the  hole 

previously  drilled  in  the  ceiling,  mark  the 

spot  where  the  vent  will  penetrate  the  roof. 

Determine  if  ceiling  joists,  roof  rafters,  or 

other framing will obstruct the venting system. 

You may wish to relocate the appliance, or to 

offset, to avoid cutting load bearing members.

STEP 3.

  To install the Round Support Box/Wall Thimble 

in a flat ceiling, cut a 10 inch (25.4 cm) square 

hole in the ceiling, centered in the hole drilled 

in Step 2. Frame the hole as shown in Figure 

14.

STEP 4

.  Assemble the desired lengths of black pipe and 

elbows necessary to reach from the appliance 

adapter  up  through  the  Round  Support  Box. 

Insure that all pipe and elbow connections are 

in their fully twist-locked position.

Do not interfere with the structural integrity 

of the walls. 

Summary of Contents for C-10450


































Reviews: