Enviro 828 DV.FS. Owner'S Manual Download Page 25

Page: 25 / 25

17. INSTALLATION DATA SHEET

The installer for warranty purposes and future reference must record the following information.

Envirogas Models:

828.DV. FS. (Freestanding) Direct Vent Room Heater

828

DV.

INS.

(Insert)

828 DV. MH. (Mobile Home)

Name of Owner:

__________________________________________

Address:

__________________________________________

__________________________________________

Phone:_____________________________________

Name of Dealer:

___________________________________________

Address:

___________________________________________

Phone: ___________________________________

Name of Installer:

___________________________________________

Address:

___________________________________________

Phone :_____________________________________

•

Model :___________________________________

•

Serial Number: __________________

•

Date of Purchase:

__________/________/________

•

Date of Installation:

__________/________/________

•

____ Natural Gas (Nat.), ____ Propane (LPG)

•

Inlet Gas Supply Pressure: ________ in.w.c.

If the orifices were changed by the installer.

•

Front Burner Orifice # __________ ,

•

Back Burner Orifice # __________ .

•

Pilot Orifice # ________ or ______ in.Dia.

E-MAIL ADDRESS (

[email protected]

)

WEB SITE ADDRESS (www. Enviro-fire.com)

MANUFACTURED BY:

SHERWOOD INDUSTRIES, 6782 OLDFIELD RD., SAANICHTON, B.C., CANADA V8M 2A3

Summary of Contents for 828 DV.FS.


























Search results

Summary of Contents for 828 DV.FS.

Reviews:

Brands by name

Popular brands

Enviro 828 DV.FS., Owner'S Manual

Search results

Summary of Contents for 828 DV.FS.

Reviews:

Brands by name

Popular brands