background image

© COPYRIGHT 2016 ENTERGIZE, LLC.  ALL RIGHTS RESERVED.

      

P/N 71969 3220-2345  REV 00=E 

2

SETBACK OPERATION NOTES

The T8532OCC Thermostat has an onboard occupancy sensor that will setback 

operation when a room becomes vacant. Service Menu 

325 Occupied Sensor 

Operation

 is turned on to enable this operation.

Occupied Timer (SM 326) 

- Sets the amount of time that must pass without a 

detection before the control goes to Setback and starts the Ramping process. 

Setback Ramping (SM 327) -

 Determines how the control will ramp to setback 

values.  Economy setting goes directly to setback values. Comfort 1 setting will 

allow a 1°F per hour setback of the control set point. Comfort 2 sets back at 2°F 

per hour until the selected setback value is reached.

Setback Values (SM 310 and SM 320) 

- Set the HEAT and COOL set points for 

setback. Values can be set to OFF or 50-90F. Selection of OFF will result in a 

set point of OFF.

Night Lock ON Protection (SM 328) 

– When enabled the control holds the 

user set point between 10 PM and 8 AM, anytime occupancy is detected during 

that time period. Note: This control has Low/ High Temp Protection. Freeze 

protection on this control is set at 40°F (heat). Over temp protection is set at 

110°F (cool).

Occupancy Sensor Detection Performance

Detection Distance: 16.4 Ft (5 meters)

Detection Range: 94° Horizontal x 82° Vertical

Input Power: 

24 VAC (20-30 VAC) 50/60 Hz and/or 2 AA 

Batteries

Output Rating

Terminal W,Y,A - 20-30 VAC 0.02-1.0 A

Terminal G - 20-30 VAC 0.02-0.6 A

Total Load not to Exceed 2.5 A

Temperature Control 

Range:

50° to 90° F (10° to 32° C)

Operating Temperature 

Range:

0° to 120° F (-18° to 49° C)

MENU

 

FEATURE

OPTIONS

STD. DEFAULT

DESCRIPTION / COMMENTS

100

Schedule Format

0-3

1

Select the schedule format on the T8000 Series. (Menu not available on non-programmable 

thermostats.) NOTE: Set the clock before changing to non-progammable. 

0 =   nonprogrammable 

1 =   programmable

2 =   5-1-1 schedule 

3 =   5-2 schedule 

101

Daylight-Saving 

Time

0,1

0

Select daylight-saving time as it follows standard format in U.S.: It begins second Sunday of 

0 =   Disabled 

1 =    Enabled (2007 U.S. Format)

110

System Type

1-13

1

1 =   1 Heat/1 Cool conventional

2 =   1 Heat/1 Cool heat pump

3 =   Heat only without fan (2-wire systems)

4 =   Heat only with fan

5 =   Cool only

6 =   2 Heat/1 Cool heat pump (with auxiliary heat) and Emergency (Em) heat

7 =   2 Heat/2 Cool multistage conventional

8 =    2 Heat/ 1 Cool multistage conventional

9 =    1 Heat/ 2 Cool multistage conventional

10 =   2 Heat/ 2 Cool heat pump (no auxiliary heat)

11=   3 Heat/ 2 Cool heat pump (with auxiliary heat) and Emergency (Em) heat

12 =   NA

13=   NA

120

Fan Control 

(heating)

0,1

1

0 =   Fossil Fuel; Gas/Oil/Propane heat (equipment controls heating fan)

1 =   Electric Furnace (thermostat controls heating fan)

121

Fan Speeds

1, 2, 3, 4

3

Allows selection of multiple fan speeds. 

1  =   Single speed Fan (G terminal) 

2  =   2-speed Fan (G and E Terminals) 

3  =   3-speed Fan (G,A and E Terminals) 

4  =   3-speed Staged Fan 

130

O/B  Reversing 

valve

0,1

0

When 0, output is active for cooling. When 1, output is active for heating.

0 =   (O) Active with cooling

1 =   (B) Active with heating

135

W1 Output 

0,1

0

Changes operation of W1 for Active to Open (NC Normally Closed) to Active to Close (NO  

Normally Open).

0 =   NC Operation

1 =   NO Operation

150

Backlight

0,1

0

0 =   Backlight temporarily on

1 =   Backlight always on (low intensity, 24V only)

Table 2.  advanced configura

Tion: S ervice  Menu S

Some Service Menus may not be available, depending on system type (SM 110). 

Summary of Contents for T8532OCC

Page 1: ...ectrostatic discharge to thermostat CAUTION Do not connect unused wires together ALL ELECTRICAL LOADS MUST BE CONNECTED TO TERMINAL C 24 VAC TABLE 1 TERMINAL BLOCK Fan Coil Conventional Heat Pump C 24 VAC Unswitched side C 24 VAC Unswitched side W1 Stage 1 Heat B O Reversing Valve W2 Stage 2 Heat AUX Auxiliary Heat Stage 2 or 3 G FAN High G FAN High A FAN Medium A FAN Medium E FAN Low E FAN Low Y1...

Page 2: ...F 18 to 49 C MENU FEATURE OPTIONS STD DEFAULT DESCRIPTION COMMENTS 100 Schedule Format 0 3 1 Select the schedule format on the T8000 Series Menu not available on non programmable thermostats NOTE Set the clock before changing to non progammable 0 nonprogrammable 1 programmable 2 5 1 1 schedule 3 5 2 schedule 101 Daylight Saving Time 0 1 0 Select daylight saving time as it follows standard format i...

Page 3: ...etpoint thermostat will Heat to when in Setback mode Off sets Heating to 45F Setback 0 Off 50 82 F 11 27 C 320 Setback High Off 58 90 F 78 F Temperature setpoint thermostat will Cool to when in Setback mode Off sets Cooling to 150F in Setback 0 Off disabled 58 90 F 11 32 C 325 Occupied Sensor Operation 0 1 1 0 Disabled 1 Occupancy Operation ON 326 Occupied Timer Duration 30 min 1 2 4 6 8 16 20 24 ...

Page 4: ...nd 502 501 Intermittent Fan On Time 1 60 minutes 5 minutes 502 Intermittent Fan Off Time 0 60 minutes 25 minutes A selection of 0 will result in continuous Fan 520 Default Display Icons 0 4 0 Select icons that will be displayed in the Default Display screen 0 Time Temp SP 1 Time Temp 2 Time only 3 Temp only 4 No Display 530 Revision displayed 540 Factory Default Reset 0 1 0 When Enable is selected...

Reviews: