Preparing to Install into a Matrix E7, N1, N3, N5, or N7 Chassis
DFE-Platinum Series Hardware Installation Guide 3-7
Preparing to Install into a Matrix E7, N1, N3, N5, or N7 Chassis
To
install
any
module
into
the
Matrix E7
chassis,
refer
to
“
Backplane
Connections
and
Installation
Rules
”
on
page 3
‐
3
to
familiarize
yourself
with
the
FTM1
and
FTM2
backplane
connections
and
the
module
hardware
installation
rules.
Then
proceed
as
follows
to
prepare
the
DFE module
for
installation.
To
install
a
DFE
module
into
a
Matrix E7,
Matrix N1,
Matrix N3,
Matrix N5,
or
Matrix N7
chassis,
proceed
as
follows
to
prepare
the
module
for
installation.
1.
Remove
the
blank
panel
covering
the
slot
in
which
the
module
will
be
installed.
All
other
slots
must
remain
covered
to
ensure
proper
airflow
for
cooling.
(Save
the
blank
plate
in
the
event
you
need
to
remove
the
module.)
2.
Remove
the
module
from
the
shipping
box.
(Save
the
box
and
packing
materials
in
the
event
the
module
needs
to
be
reshipped.)
3.
Locate
the
antistatic
wrist
strap
shipped
with
the
chassis.
Attach
the
antistatic
wrist
strap
to
your
wrist
and
plug
the
cable
from
the
antistatic
wrist
strap
into
the
ESD
grounding
receptacle
at
the
upper
right
corner
of
the
chassis.
4.
Remove
the
module
from
the
plastic
bag.
(Save
the
bag
in
the
event
the
module
must
be
reshipped.)
Observe
all
precautions
to
prevent
damage
from
Electrostatic
Discharge
(ESD).
Caution:
Failure to observe static safety precautions could cause damage to the module.
Follow static safety handling rules and wear the antistatic wrist strap.
Do not cut the non-conductive bag to remove the module. Sharp objects contacting the
board or components can cause damage.
Precaución:
Si no toma las medidas de seguridad necesarias para evitar descargas de
electricidad estática, es posible que el módulo se dañe. Siga los consejos de seguridad
para la manipulación del producto y no olvide utilizar la pulsera antiestática.
No corte la bolsa antiestática para sacar el módulo. Tenga en cuenta que si algún objeto
cortante entra en contacto con la placa o con los componentes, éstos podrían dañarse.
Warning:
Install this module in a Matrix E7, N1, N3, N5, or N7 chassis that has been
installed in a Restricted Access Location only. Access to the equipment by users must be
restricted through the use of a tool or lock and key or other means of security and is
controlled by the authority responsible for the location.
Advertencia:
Instalar este modulo en un Matrix E7, N1, N3, N5, o N7 que ha sido
localizado en un lugar de Acceso Restringido. Aceso al equipo debe ser restringido por el
responsable del sitio.
Warnhinweis:
Installieren Sie dieses Modul nur in einem E7, N1, N3, N5, oder N7
Chassis, wenn sich diese in einer zugangsgeschützten Umgebung befinden. Der Bereich
zu den Komponenten sollte durch ein Schloß, einen Schlüssel oder sonstigen
Sicherungen geschützt und durch einen Verantwortlichen kontrolliert werden.
Summary of Contents for Matrix 7H4385-49
