Ensy AHU-300 HH User Manual And Installation Manual Download

Page: 23 / 36

393870-2 Rev 0: 11.07.2018 BBV

We reserve the right to change technical data without notice.

http://www.ensy.no

Page 22

TECHNICAL DATA

Reheating unit + fans

- phase/voltage

(50Hz/VAC)

1 / 230

- power consumption

(W)

1200

Recommended fuses

(A)

Control system

Integrated

Filter Class

Superpleat

Thermal/sound insulation

(mm)

Weight, including brackets

(kg)

49,5

SPECIFICATIONS

•

Rotary heat exchanger with heat recovery up to 85 % efficiency.

•

Electric heating coil.

•

High efficiency and low noise EC fans. Adjustable 30 to 100 % speed.

•

Adjustable supply air temperature between 15 and 21°C.

•

Acoustic and thermal-insulated housing.

•

Control system with "Touch Panel" for the control of the unit supplied as standard and to be

connected outside the unit on “STYREPANEL 1” See page 19 or 20.

•

The unit is designed for optional connection of a cooker hood on the side of the unit.

In the end of unit there is:

(Look at page 19 and 20)

•

Junction point of contact for connection for an extra control panel. (STYREPANEL 2)

•

Junction point of contact for cooker hood. (KV)

•

Junction point of contact for Co² sensor. (CO ²)

•

Junction point of contact for pulse switch. (D1)

•

Junction point of contact for an external humidity sensor or motion detector. (D2)

•

Junction point of contact for connection for home / away function. (D3)

EXTRA

Extra control panel, desire more control points. Including 10 meters signal cable (Art. no: 0100051-2)

Wireless pulse switch. (Art. no: 0100052-2)

Suspension bracket for wall. (Art: 01008045-2) Look at page 17.

Summary of Contents for AHU-300 HH





































Search results

Summary of Contents for AHU-300 HH

Reviews:

Related manuals for AHU-300 HH

Brands by name

Popular brands

Ensy AHU-300 HH, User Manual And Installation Manual

Search results

Summary of Contents for AHU-300 HH

Reviews:

Related manuals for AHU-300 HH

Brands by name

Popular brands