manualshive.com logo in svg

ENS SIP46B5/28-H, User Manual, Page: 102 / 197

Share
Download
ENS SIP46B5/28-H User Manual Download Page 102

Network Camera User Manual 

101 

 

 

Purpose: 

You can specify a target area on the live video, and then the specified video area can 

be displayed via the third stream in certain resolution, providing more details of the 

target area if needed.   

Note:

 Target cropping function varies according to different camera models. 

Steps:   

1.

 

Enter the 

Target Cropping

 settings interface. 

2.

 

Check 

Enable Target Cropping

 checkbox to enable the function. 

3.

 

Set Third Stream as the stream type. 

4.

 

Select the cropping resolution for the video display of target area. A red rectangle 

is displayed on the live video to mark the target area, and you can click-and-drag 

the rectangle to locate the target area as desired. 

5.

 

Click 

Save

 to save the settings. 

Summary of Contents for SIP46B5/28-H






































































































































































































Reviews:

No comments