enphase IQ 7 Installation And Operation Manual Download Page 41

Page: 41 / 43

IQ 7 / IQ 7+ / IQ 7X / IQ 7A with EN4 Bulkhead Installation and Operation

141-00047-01

Q Cable Specifications

Specification

Value

Voltage rating

600V

Voltage withstand test (kV/1min)

AC 3.0

Max DC conductor resistance (20º

C) (Ω/km)

5.433

Insulation resistance (20ºC)

≥20M (Ω/km)

System temperature range (ambient)

-40ºC to +65ºC (-40ºF to 149ºF)

Cable temperature rating

90ºC Dry / 90ºC Wet

Cable rating

Certification

UL 3003, TC-ER equivalent

Flame test rating

FT4

Cable conductor insulator rating

THHN/THWN-2

Environmental protection rating

IEC 60529 IP67 NEMA 6

UV resistance

720h

Compliance

RoHS, OIL RES I, CE, UV Resistant, combined UL for Canada
and United States

Conductor size

12 AWG

Maximum loop size

12 cm (4.75

“)

Flat cable dimensions

6 mm x 9.5 mm (0.2” x 0.37”)

Sealing cap dimensions

38.6 mm x 20 mm

(1.5” x 0.7”)

Cable connector dimensions

20 mm x 1.1 mm x 6.5 mm

(0.7” x 0.04” x 0.25”)

Enphase Connector Ratings

Enphase Connectors on the cable assemblies in the following table have a maximum current of 20 A, a
maximum OCPD of 20 A, and maximum ambient temperature of -40° to +79° C (-40° to +174.2° F) and
are rated for disconnection under load.

Part Number

Model

Maximum Voltage

840-00387

Q-12-10-240

250 VAC

840-00388

Q-12-17-240

250 VAC

840-00389

Q-12-20-200

250 VAC

860-00311

ECA-EN4-S22

80 VDC

860-00315

ECA-EN4-S22-L

80 VDC

860-00312

ECA-EN4-FW

80 VDC

Summary of Contents for IQ 7











































Search results

Summary of Contents for IQ 7

Reviews:

Related manuals for IQ 7

Brands by name

Popular brands

enphase IQ 7, Installation And Operation Manual

Search results

Summary of Contents for IQ 7

Reviews:

Related manuals for IQ 7

Brands by name

Popular brands