manualshive.com logo in svg

enphase BRK-100A-2P-240V, Quick Install Manual, Page: 1 / 12

Share
Download
enphase BRK-100A-2P-240V Quick Install Manual Download Page 1

  Q U I C K

  I N S T A L L  

G U I D E

 

Model number: EP200G101-M240US01

Install the Enphase 

IQ System Controller 2 

To install the Enphase

 

IQ System Controller 2 and the Enphase IQ System Controller 2 wall-mount bracket, read and follow all warnings and instructions in this 

guide and in the 

Enphase IQ System Controller 2 Installation and Operation Manual

 at 

enphase.com/support

. Safety warnings are listed on the back of this 

guide. These instructions are not meant to be a complete explanation of how to design and install an energy storage system. All installations must comply with 

national and local electrical codes and standards. 

Only qualified electricians shall install, troubleshoot, or replace the IQ System Controller 2.

The Enphase Energy System includes the Enphase IQ System Controller 2 with Microgrid Interconnection Device (MID) capability, which 

consolidates interconnection equipment into a single enclosure and streamlines grid-independent capabilities of PV and storage installations 

by providing a consistent, pre-wired solution for residential applications. Along with MID functions, it includes PV, storage, and generator input 

circuits.

©2021 Enphase Energy. All rights reserved. Enphase, the Enphase logo, IQ System Controller 2 , IQ Battery, IQ Gateway, IQ combiner, IQ microinverter, Enphase 

App and other trademarks or service names are the trademarks of Enphase Energy, Inc. Data subject to change. Rev02-10-25-2021

Scenario 1:                                                                  

Whole home backup with IQ System 

Controller as service entrance: 

This 

is the preferred configuration for back 

up of the entire main load panel. This 

configuration supports up to an 80A 

breaker each for the PV circuit, battery 

storage and Generator(optional). 

Scenario 2:                                                               

Partial home backup with main load 

panel as service entrance: 

This is 

the preferred configuration for partial 

home backup with subpanel with 

PV and IQ Battery. Generator can be 

integrated with IQ System Controller 

based on the homeowner’s needs.

Scenario 3:                                                   

Whole home backup with Solar 

Only backup: 

This is the preferred 

configuration for backup of the entire 

main load panel using only IQ8 PV. 

Generator can be integrated with 

IQ System Controller based on the 

homeowner’s needs.

(optional)

(optional)

(optional)

Summary of Contents for BRK-100A-2P-240V













Reviews:

No comments