Enovation Controls Murphy PowerView PV101-C User Manual Download Page 43

Page: 43 / 52

00-02-0796

- 37 -

2013-04-08

Troubleshooting



WAIT TO START PREHEATING

is displayed

The ECU is broadcasting a 'Wait to Start' message. Engine

manufacturers typically recommend against starting the

engine while the ECU is broadcasting this message. Once

the ECU stops broadcasting this message, this screen will

no longer be displayed on the PowerView.



CANBUS FAILURE

is displayed

The PowerView has not received any valid J1939 CAN

messages for at least 30 seconds. Check wiring, CANBUS,

termination resistors, and Engine ECU address in the OEM

Menu.



TIMEOUT ECU NOT RESPONDING

is displayed

The PowerView sent a request to the ECU for Stored Fault

Code (DM2) information, and the ECU did not respond to

the request. This message on the PowerView indicates the

ECU may not support Stored Fault Code (DM2) functionality

over J1939.

Summary of Contents for Murphy PowerView PV101-C





















































Search results

Summary of Contents for Murphy PowerView PV101-C

Reviews:

Related manuals for Murphy PowerView PV101-C

Brands by name

Popular brands

Enovation Controls Murphy PowerView PV101-C, User Manual

Search results

Summary of Contents for Murphy PowerView PV101-C

Reviews:

Related manuals for Murphy PowerView PV101-C

Brands by name

Popular brands