manualshive.com logo in svg

Enotec AQUATEC 1000, Installation And Operation Manual

Share
Download
Enotec AQUATEC 1000 Installation And Operation Manual Download Page 14

Installation

 

Installation and Operation Manual – AQUATEC 1000 

14 

Doc.-ID: AQUA_16012020_EN 

2.9 

Adjusting the V-shield / filter head 

 

 

Before installing the probe, 

the direction of flue gas flow must be determined

 and the filter head assembly turned 

to such a position that the V-shield faces the oncoming flue gas. The filter head can be turned freely a full 360° for 
this purpose, by loosening the counter nut, loosening the Allen screw and rotating the filter head / V-shield to the  
required position, and then tightening the Allen screw and counter nut. 

 

 

 

  Flue gas direction 

  V-shield (KES-132X/KES-200X) 

  V-shield ( KES500X) 

  Screws to secure filter head 

  Filter head 

  Rotation of filter head 

  Probe 

Figure 11 -

 Adjustment of the V-shield 

 

 

 

Loosen the locknut 

 

Loosen the locknut 

 

Adjust the filter head.

 Adjust the position of the 

shield against the flow direction

  

Tighten the locknut

 

Tighten the locknut 

 

 

Figure 12 -

 Adjustment the fitter head 

 

 

 

 

 
 

 

 

1

2

3

4

Summary of Contents for AQUATEC 1000






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands