manualshive.com logo in svg

Enotec AQUATEC 1000, Installation And Operation Manual

Share
Download
Enotec AQUATEC 1000 Installation And Operation Manual Download Page 13

Installation and Operation Manual – AQUATEC 1000 

Installation

 

Doc.-ID: AQUA_16012020_EN 

13 

2.7 

Installation of the probe 

The flue gas temperature, pressure and all other process conditions must be in accordance with the specification. 
Leave enough space for insertion/removal of the probe and protection tube (if supplied) and ensure access to the 
measuring probe and/or connecting box. Before cutting a hole in the flue gas duct, make sure that the inside of the 
duct has enough space for probe installation and that no soot is blown out nearby or any obstacles are in the way. 
For probe lengths exceeding 2000 mm, a support must be mounted inside the duct (every 2m) to prevent the probe 
and mounting tube from flexing or bending. 

ENOTEC recommends installing the probe horizontally for the  

fastest possible response time. 

 

 

 

 

 

 

 

 

 

 

Maintain the protection class 

 

Avoid vibrations greater 2g 

 

 

2.8 

Mounting of the Probe  

 

 

The mating flange must be 
welded at the specified angle 

Process gas flow 

The welded seam must be gas-
tight 

Adapter (supplied by customer) 

Stainless steel adapter with 
R2½”-thread 

AQUATEC – Probe 

Insulation 

Figure 9 - 

Mounting the 

KES 132x with filter head KES-132060AK and adapter plate ASR-1320-KN 

 

 

Figure 10 - 

Mounting of the O

2

 probe KES-132x with ASR-1320 

1-

3°

1

3

4

5

6

2

7

AQUATEC

Summary of Contents for AQUATEC 1000






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands