background image

 

1.2 Typical Applications 

 

• 

Building installation 

• 

Industrial automation 

• 

Consumer electronics 

 

Key applications are wall-mounted flat rocker switches with 1 or 2 rockers (with medial 
position), as well as handheld remote controls with up to 4 single pushbuttons. 

 
The PTM 200 device is part of a powerful RF system solution from EnOcean for operation and 

control applications. Because the RF transmitters are self-powered (no batteries), 
maintenance-free RF systems are possible. The RCM devices operate together with the 

following additional EnOcean components: RCM (general-purpose radio receivers), STM (solar-
powered wireless sensors), CTM (remote control) and TCM (bi-directional IT interface and 
repeater). 
 
 
 

1.3 Features Overview 

Power supply: ......................................................... power generation by rocker pressing  
                                                                                      (Electro-dynamic Power Generator) 
Frequency:...................................................................................................868.3 MHz 
Transmission power:.................................................................................max. 10 mW 
Modulation type:...................................................................................................ASK 
Data rate: ......................................................................................................120 kbps 
Channel bandwidth: ........................................................................................ 280 kHz 
Antenna:...................................................................................................... integrated 
Transmission range: ................................................................ approx. 300 m free field 
Telegram packet length (sub-telegram):................................................ 0.9 ms +/-5% 
No. of (redundant) packets: ....................................................... 3 within approx. 40 ms 
Number of channels:................................................ 2 channels with 4 action states each  
                                                                   (upper/lower contact nipple is pressed/released) 
Telegram type: ........................................................................................RPS of type 2  
                                              (allows interpretation of operating two buttons simultaneously) 
Device identifier:  ............................................ individual 32-bit ID (factory programmed) 
 

 

 

 

 
©EnOcean GmbH, A. Anders 

 

Page 5 of 22 

 

 PTM 200 User Manual V1.1 

 

Summary of Contents for PTM200























Reviews: