9
10
12
14
13
15
16
11
9 MIDI THRU
Standard 5-pin diode jack. It sends incoming MIDI data from the MIDI IN jack to another connected
MIDI device.
10 MIDI IN
Standard 5-pin diode jack. It receives MIDI data from your MIDI footswitch.
This jack also supplies the current for the ENGL MIDI Footcontroller Z-12.
11 POWER SUPPLY SELECTOR SWITCH
This switch activates the power supply to the ENGL MIDI Footcontroller Z- 12 via the MIDI
cable. In position x (left), the power supply of the Switcher is routed via Pin 1 and Pin 2 of the
MIDI IN port. If you use a MIDI footswitch of a another brand, set the switch to the right
position to prevent damage to the MIDI footswitch. If the footswitch is also equipped with a
phantom power circuit, refer to the footswitch user´s manual to determine which pins are
used to route the power supply as well as the voltage and current values. If the voltage and
power routing specifications are identical, you can set the switch to the left position to route
power to the MIDI footswitch via the MIDI cable.
PLEASE HEED THE FOLLOWING: A standart AC power pack provides approx. 300mA
of current. The Switcher requires a maximum of 140 mA; a MIDI footswitch that is powered
remotely via the AC power pack may not consume more than 160 mA of current, otherwise
a bigger AC power pack must be used. To feed the Switcher and the ENGL Footcontroller Z-12
with current a standart power pack is sufficient.
12 LOOP 1 & 2
Switch LOOP 1 and Switch Loop 2 are routed to this 1/4" stereo jack. These two switch loops are set
via buttons (3) and (4). The first contact of Switch Loop 1 is located on the tip of the 1/4" plug and
the second contact on the bottom portion of the plug, along with the second contact of Switch Loop 2
(usually ground). The first contact of Switch Loop 2 is located at the shielded portion of the plug,
midway between the tip and the base.
13 LOOP 3 & 4
Switch LOOP 3 and Switch Loop 4 are routed to this 1/4" stereo jack. These two switch loops are set
via buttons (5) and (6). The first contact of Switch Loop 3 is located on the tip of the 1/4" plug and
the second contact on the bottom portion of the plug, along with the second contact of Switch Loop 4
(usually ground). The first contact of Switch Loop 4 is located at the shielded portion of the plug,
midway between the tip and the base.
14 LOOP 5
This 1/4" mono jack is connected to Switch Loop 5 and is set via buttons (7). The first contact of
Switching Loop 5 is located on the tip of the1/4" plug and the second contact on the
bottom portion of the plug (usually ground).
15 LOOP 6
This 1/4" mono jack is connected to Switch loop 6 and is set via buttons (8). The first contact of
Switching Loop 6 is located on the tip of the1/4" plug and the second contact on the
bottom portion of the plug (usually ground).
16 POWER SUPPLY
Power supply jack for the MIDI Switcher. Insert the AC power
pa
ck's plug to this
jack. The polarity is irrelevant. The Switcher is ready to operate as soon as you have
connected the requisite current to this jack. Please ensure that a switchable universal AC power pack
is set to a minimum of 9 volts and when you are feeding power to a MIDI footswitch, to a
minimum of 12 volts.
REAR PANEL
M
IDI
T
HRU
M
IDI
I
N
SERIAL NO.
L
OOP
1 & 2
C
OM
. 2 1
L
OOP
5
L
OOP
6
MIDI SWITCHER, TYPE Z-11
MADE IN GERMANY
POWER SUPPLY
7-14 Volts AC
9-20 Volts DC
300 mA
M
IDI
F
OOTCONTROLLER
Z-12
x
L
OOP
3 & 4
C
OM
. 4 3
