background image

 

M-TRAC1

 

 

IOM-55 

 

May 2019 

 

DIP SWITCHES 

 
The M-TRAC1 options are configured by DIP switch selection and/or wiring connections.  DIP 
switch settings are noted on the internal wiring diagram, and should not be altered. 
 

TABLE 2 

DIP SW 

Description 

10 

Disable Auto Heat Switch.  If enabled the M-TRAC1 will monitor the discharge air 
temperature and disable the heat if the temperature is constantly greater than 
the Setpoint (> 3˚F). 

Extended Profile Velocity Range.  Allows the M-TRAC1 to be compatible with 
older equipment. 

Service Mode. Enable to manually control the firing rate. 

Air Priority Program.  See Blower Control. 

16 Second Pre-purge.  Heating will delay on after fan starts. 

Slow Opening Valve.  See Modulating Valve Light Off Position. 

Disable Open Sensor Checking.  See Discharge Air Setpoint. 

Disable Low Limit.  See Low Limit. 

Alarm contact to be used for reverse interlock.  See Reverse Interlock. 

2-10 Vdc Set Point Reset.  See Temperature Reset. 

Note: Table based on model M-TRAC 1.4.3 

 

INDICATION AND DIAGNOSTIC LIGHTS 

 
There are 5 status lights on the M-TRAC1 labeled A to E.  They operate in 4 patterns:  an 
irregular flash (.. __ .. __ ..), fast flash (…….), slow flash (. . .), or constantly on (_____).  

TABLE 3 

IRREGULAR 

FAST 

SLOW 

ON 

LIGHT 

System Lockout 

System Lockout 

System 
Problem 

System 
Ok 

A – GREEN  

Wiring Or Flame 
Relay Problem 

Prepurge Or Valve 
Positioning Delay 

Limit Open 

Ignition 
Attempt 

B – RED  

Air Flow Or M-TRAC 
Problem 

Air Velocity Very Low 

Air Velocity Too 
Low 

Air Velocity Too 
High 

C – RED  

Service Mode 

Ignition Failure 

Heat Switch Open  Burner On 

D – RED 

Open Discharge      
Sensor 

Discharge Temp Low  Fan Switch Open 

Damper Open 
Delay 

E – RED  

 

 
 
 
 
 
 

Summary of Contents for EngA M-TRAC1




















Reviews: