5A
Ignition coil
* DIODE 1N4001
(optional)
Fuel
Pump
Constant
+12VDC
Ignition Coil
(White tube, Circuit 2)
Switched
+12VDC
Ignition (Purple label)
Starter Solenoid
(Red tube, Circuit 1)
Spare Armed Output to cut fuel pump
(Brown label, circuit 3)
30
85
86
87
87a
NOTE: This wire must
show +12V when the
ignition switch is in the
ON and START position.
+12VDC (Red label)
Ground (Black label)
Ground (Black label)
5A
Ignition coil
* DIODE 1N4001
(optional)
Fuel
Pump
Constant
+12VDC
Ignition Coil
(White tube, Circuit 2)
Switched
+12VDC
Ignition (Purple label)
Starter Solenoid
(Red tube, Circuit 1)
Spare Armed Output to cut fuel pump
(Brown label, circuit 3)
30
85
86
87
87a
NOTE: This wire must
show +12V when the
ignition switch is in the
ON and START position.
+12VDC (Red label)
Ground (Black label)
Ground (Black label)
LED MOUNTING
1.
Ask the customer where to mount the LED.
2.
It must be easily visible from any direction, but should
not be exposed to direct sunlight.
3.
To mount:
a.
Press the LED out of its plastic receptacle.
b.
Drill an 8mm hole in the desired LED location.
c.
Press the receptacle into the hole from the front.
d.
Press the LED into the receptacle from behind.
TESTING THE INSTALLATION
When the installation is complete, follow the Owner’s
Manual and completely test the unit.
MOUNTING THE CONTROL MODULE
Screw it onto the car body out of sight, or cable-tie to the
vehicle’s wire harness or other suitable location.
DEACTIVATION COIL INSTALLATION
NOTE
: Be sure to inform the customer if you choose to
install the deactivation coil in a location other than
those shown below.
SLI-762PP-ISS CONNECTION DIAGRAM
NOTES:
1. PURPLE label
ignition wire
must be connected at all times
for proper operation.
2. RED label
power wire must be
connected via 5A fuse.
3. Circuit 1 or Circuit 2
must be
used to disable the starter in
order to be consistent with
explanations in the Owner’s
Manual.
(Black label)
(Black label)
Two separate sources
of chassis ground.
.
.
5A
(Red
2
label)
Constant
+
12VDC
(Purple
1
label)
Switched
+ 12VDC
LED
Black 2-strand
Deactivation
Coil
(White label)
N.O. door (—) switch
Circuit 2
3
Circuit 1
3
(Green label) Circuit 3
NOTE
—This wire
must show + 12V
when the ignition
switch is in the ON
and START position.
Black heat shrink
Black heat shrink
Below
ignition
cylinder
Best Range
Inferior Range
Correct
Incorrect
Too far back
Angle faces away
from key
Touches the
cylinder
Around
ignition
cylinder
Best Range
Inferior Range
No bends or kinks
in the antenna
Antenna is bent
5A
Ignition coil
* DIODE 1N4001
(optional)
Fuel
Pump
Constant
+12VDC
Ignition Coil
(White tube, Circuit 2)
Switched
+12VDC
Ignition (Purple label)
Starter Solenoid
(Red tube, Circuit 1)
Spare Armed Output to cut fuel pump
(Brown label, circuit 3)
30
85
86
87
87a
NOTE: This wire must
show +12V when the
ignition switch is in the
ON and START position.
+12VDC (Red label)
Ground (Black label)
Ground (Black label)
NOTICE:
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and
improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
SECO-LARM
®
U.S.A., Inc
.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
E-mail: [email protected]
reproduced or copied, in whole or in part, without the written permission of SECO-
LARM.
PITTW3
.docx
mi-SLI-762PP-ISS_1106.docx
.docx
