WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period
of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any
defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or
abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes
other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no event
shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.
NOTICE:
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one
of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice.
SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2015 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without
the written permission of SECO-LARM.
SECO-LARM
SECO-LARM
SECO-LARM
SECO-LARM
SECO-LARM
®
U.S.A., Inc.
U.S.A., Inc.
U.S.A., Inc.
U.S.A., Inc.
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
PITSW1
Website: www.seco-larm.com
E-mail: [email protected]
FILE: DT/DTP/MiSK9x9TDWS-BQ_150205.pmd
ORDER PART# 762-103-2%
Battery
Battery Operated 12VDC Output
Adapter
Power on
Transmission
Push-Button
or contact
12VDC Alkaline
battery included
12VDC output
adapter is optional
Example Connection Diagrams:
12VDC
Adapter
INSTALLATION:
1.) Power Connection
–
The wired transmitter can be
powered by the factory preinstalled one 12VDC
alkaline battery or by an external 12VDC output
regulated adapter (not included).
If an external power adapter is preferred, connect
the red & black wires of the wired transmitter to the
adapter’s output wires. Must observe correct wire
polarity. Red wire is for positive and black wire is
for negative.
NOTE: a) The power input range of the wired
transmitter unit is between 9~13.8VDC,
connecting more than 13.8VDC power or
reversing the polarity will burn out the unit
and void the warranty.
b) Use only 12VDC output “regulated” adapters
to power the wired transmitter.
c) Factory had preinstalled one 12VDC alkaline
battery inside wired transmitter unit. If it is
necessary to connect an external adapter,
removed first the internal alkaline battery,
otherwise the internal battery will become
defective.
2.) External Switch
Connection –
Aside from its own
built-in single button, the wired transmitter can also
be controlled by an external N.O. pushbutton / sensor
switch (not included), or use both the built-in &
external switches (see Example Connection Diagram
below). If an additional external N.O. switch is
necessary, connect the two blue wires to the switch
terminal.
NOTE: If the red & black or the two blue wire pairs are
not being use, the tip of the wires (where the
copper wires are exposed) must be cut or
wrapped to avoid a short circuit.
