background image

www.enersys.com

Inter-Cell Connectors

The connections are made by bolting the supplied plated 

copper inter-cell and intermodule connectors to the cell 

posts of opposite polarity on adjacent cells. See ASSEMBLY 

DRAWING for details.

1.  Clean the contact surface of the inter-cell connector using 

a stiff-bristle nonmetallic brush/pad. Be careful not to 

remove the plating with excessive brushing.

2.  Apply a light coat of heated NO-OX-ID grease to the 

contact surface of the inter-cell connector and terminal 

post with a small paintbrush.

3.  Bolt all inter-cell connectors according to the ASSEMBLY 

DRAWING. Assemble as the example shown in Figure 25 

and below list:

NOTE:
Stamped flat washers may have one sharp edge. Install 

the washer with the sharp edge away from the plated 

copper inter-cell connector to avoid damaging the 

plating

  •  Hex Bolt
  •  Flat Washer
  • Connector
  •  Battery Post
  • Connector
  •  Flat Washer
  •  Lock Washer
  •  Hex Nut

NOTE:
Inter-cell connections vary in length depending on the 

type of connection (cell-to-cell, module-to-module, etc.) 

and/or stack configuration.

4.   Secure all connections finger-tight to allow for some 

adjustment of position.

5.   After all connections are completed, torque all to 85 in-lbs.

 

6.   Apply a light coat of heated NO-OX-ID grease to the bolted  

connection with a small paintbrush.

INSTALL INTER-CELL CONNECTORS

FIGURE 25

18

Summary of Contents for PowerSafe DDm 100-21

























Reviews: