background image

20

LED icons

1. Hot water available

The icon indicates that the domestic hot water temperature reaches the set point. The hot water
is available for use. Heat pump is standby.

2.

Fan ventilation

The icon indicates that the fan ventilation function is enabled.
When the unit is on, press the

button and hold it for 5 seconds the fan ventilation function

can be enabled or disabled. If this function is enabled the fan will continue working to ventilate
the air, when the water temperature reaches the set point and unit is standby. If this function is
disabled the fan will stop, when the water temperature reaches the set point and unit is standby.

3.

Electrical heating

The icon indicates that the electrical heating function is enabled. The electrical heater will work
according to the control program.

4.

Defrosting

this icon shows the heat pump is under defrosting

5.

Heating

this icon shows the heat pump is working

6.

Key lock

The icon indicates the key lock function is enabled. The keys cannot be operated until this
function is disabled.

7. Left temperature display

The display shows the setting water temperature.
When checking or adjusting the parameters, this section will display the relating parameter
number.

Summary of Contents for AXHW-20a/200L


































Reviews: