background image

 

TAEC EcoTop Owners Manual v1.4 

 

ww

w.

ta

ec

.c

o

.n

 

16   

 

F14 

 
System 

Probes configuration 

*** 

*** 

1 probe (S1) 

Delete counters 

*** 

*** 

*** 

Anode ACI ON/OFF 

OFF 

ON 

OFF 

 
 
 

3.7

 

Disinfect Function 

 

Eco’s electronic control features 

a

 Disinfect

 function, which consists of a water heating cycle 

increasing the temperature to a higher temperature for a period long enough to prevent the 
formation of germs inside the tank.  The 

Disinfect

 function can be set automatically or manually.  

 
The NZ Building Code G12 regulation regarding protection of hot water storage from Legionella is 
daily to greater than 60°C, or weekly to greater than 60°C for 1 hour). 
The installer must set the disinfect function to at least weekly as required by NZ Building Code.  The 
Set point should be set to at least 62°C when using the weekly function. 
 
When automatic Disinfect mode is not activated, the user must activate it manually on the key 
Disinfect. 
At the end of the function, when the temperature reaches the Disinfect setpoint the system returns 
to the original operating mode. 
 
The 

Disinfect

 function is activated: 

 

 

When you press the 

“DISINFECT” key

 for 3 seconds 

 

On the penultimate day of the holiday period (see section 9.7).  During the holidays the 
value attributed to the parameter disinfect must be nil) 

 

Automatically when the desired time period is set in the function 

disinfec

 

The disinfect function is cancelled when you press the CANCEL (ON/OFF) or DISINFECT keys 

 

 

 

The NZ building code requires the temperature to be raised 
daily to >60°C daily, or weekly to >60°C for one-hour.   
It is recommended that the installer sets the disinfect function 
to weekly with a set point of at least 62°C 

 

 

3.8

 

Holidays Function 

 

To activate the 

Holiday

 function, you need to access the menu and set the number of days you will 

be on holiday, and your equipment will automatically enter Standby mode until the last day of 
holidays.  On the last day, the equipment will begin the Disinfect function to eliminate any 
formation of germs that appeared in the hot water cylinder during the time you were away. After 
the holidays and once the program Disinfect is over, the equipment will resume the previous mode 
selected (ECO, AUTO or BOOST). 

 

Summary of Contents for EcoTop Stainless 250i




























Reviews: