background image

WARNING: RISK OF PERSONAL INJURY.  

To avoid being burned, always hold the work 

light by its grip handle when making adjustments.

WARNING: RISK OF FIRE.  DO NOT 

place work light near flammable or combustible 

surfaces.

Extension cords

-The maximum extension cord length recommended for this work light is 49 in.  Use of 

extension cords longer than 49 in. may cuase a voltage drop that can dim the lights.

-Extension cords used with this work light must have an adequate American Wire Gauge 

(AWG) or wire size for safe, efficient use.  The smaller the gauge of the wire, the greater 

the capacity of the wire (e.g. 14-gauge wire has more capacity than 16-gauge wire).

-Use an extension cord or minimum 14-gauge (AWG) 3-conductor or higher capacity 

wire, such as 12-gauge or 10-gauge for this work light.

-Always make sure that the prongs on the plug of the extension cord are the same 

number, size and shape as those on the work light plug.

-Always be sure that the extension cord is in good electrical condition.

Storage

1. Always allow the work light to cool down completely before storing.

2. Store in a safe place, out of reach of children.

To avoid electrical shock, do not use near water or in areas where water may accumulate.  

Keep work light at least 16 ft. from pools or spas.  Keep plugs dry.  Use only Ground Fault 

Circuit Interrupter (GFCI) protected receptacles when using this work light in wet or damp 

locations.  Receptacles are available with built-in GFCI protection and are to be used for this 

measure of safety.

Always unplug work light and allow lamp head to cool.

The work light lamp heads get HOT very quickly.  Only touch the power plug or cushioned 

handle when turning the lamp heads ON or OFF.

To avoid burns, do not touch the glass lens, metal part of the lamp head while lamp is turned 

on.

Do not look directly at the lighted lamps to avoid eye injuries.

Always keep the work light away from any flammable materials.

Unplug and allow lamp to completely cool.

Do not operate work light if it has a missing or damaged lens cover.  Contact customer 

service for a replacement.  Read and follow all safety rules and operating instructions before 

first use of this product.

No assembly is required for this work light.

ON/OFF Switch

Each lamp has an on/off switch.  Press the switch toward the “ | ” symbol to turn the lamp 

on.  Press the switch toward the “O” symbol to turn the lamp off.  Always turn the work light 

off before unplugging.

Adjusting the light direction

1. The vertical angle of the lamp head can be adjusted freely to the desired angle.  The 

swivel will automatically lock to pre-determined angles.

2. Adjust horizontally by loosening the lower twist knob on the metal bracket located below 

the lamp head.  Adjust the lamp head to the desired position using the handle and retighten 

knob.

-

-

-

-

-

-

-

-

4

5

Your portable LED work light requires very little care and maintenance.  Simply clean the lens, 

lamp head and lamp stand regularly with a non-abrasive cleaner. 

Warning: Always make sure the work light is unplugged and completely cool before 

attempting to clean it.

www.energeticlighting.com

SAFETY INFORMATION

Operating Instructions

Operating Instructions

Printed in China

www.energeticlighting.com

CARE AND MAINTENANCE

TROUBLESHOOTING

Problem

Possible Solution

Corrective Action

The work light comes on, 

but the lights are 

dimmed.

Improper voltage or power 

supply.  Use of an extension 

cord longer than 49 in. can 

reduce the voltage supplied 

to the light and can cause 

dimming.  Use 14-gauge 

(AWG) extension cord with a 

cord length of less than 49 

in.

The work light will only oper-

ate on standard household 

120 V AC/60 Hz power.  Have 

power supply checked by a 

qualified electrician.

WARRANTY

This fixture is warranted to perform free from defects for three years. If it fails to do so, you may 

return it with proof of purchase to 13445 12th St., Chino, CA 91710 for replacement.

Reviews: