Eneo 220592 User Manual Download Page 23

Page: 23 / 79

Full Menu Setup

MEGA-PIXEL NETWORK CAMERA

■

Video Stream

■

Protocol

■

PTZ Control

• Do not adjust zoom/focus in low light conditions or night mode. It might cause

erroneous focusing.

Selects the video source stream to display the live view only.

Selects the network protocol out of HTTPS, HTTP, TCP or UDP.

• PUSH AF : Gets the lens to focus at the push of a button.

• FOCUS : Adjusts the lens focus manually for NEAR & FAR.

• ZOOM : Controls the lens optical zoom in/out for WIDE & TELE.

CAUTION

⑥

Window Fit : Resizes the live view display to fit

along with the display window size.

⑦

Full Screen: Resizes the live view display to fit

to the monitor resolution. ESC key returns to the

previous view.

⑧

Custom : Selects the live view display scale,

0%~200%, by the control bar.

100% is original size.

■

Display

6
7
8

Used to adjust zoom/focus manually or one-push focus automatically.

Summary of Contents for 220592
















































































Search results

Summary of Contents for 220592

Reviews:

Related manuals for 220592

Brands by name

Popular brands

Eneo 220592, User Manual

Search results

Summary of Contents for 220592

Reviews:

Related manuals for 220592

Brands by name

Popular brands