background image

R T M 3 2 0 4   G P S   T i m i n g   M o d u l e   U s e r   M a n u a l

24

C H A P T E R   T H R E E

25

R T M 3 2 0 4   G P S   T i m i n g   M o d u l e   U s e r   M a n u a l

C O N T R O L   A N D   S T A T U S   C O M M A N D S

This script modifies the 

/etc/inetd.conf

 file, which is non-volatilely stored in the FLASH disk 

/boot/

etc

 directory.  You must re-boot the RTM3204 after running this script for the changes to take effect.

  Set: 

 

 

 

inetdconfig

  RTM3204/Tycho response: 

Interactive shell script is started.

netconfig

This command starts an interactive shell script that will allow the user to configure the IP network 

subsystem of the RTM3204.  By default, the unit is configured to configure itself using the Dynamic 

Host Configuration Protocol (DHCP).  If you need to set up static IP configuration, you must run 

this script as 

root

 from the RS-232 serial I/O port during the installation process.  Refer to 

Chapter 2 

- Using netconfig to Set Up Your IP 

for details on the use of the command.

This script creates or modifies these files: 

 /etc/HOSTNAME

/etc/hosts

/etc/networks, /etc/resolv.conf 

and 

/etc/rc.d/rc.inet1

.  All of these are non-volatilely stored in the FLASH disk 

/boot/etc

 directory.  

You must re-boot the RTM3204 after running this script for the changes to take effect. 

  Set: 

 

 

 

netconfig

  RTM3204/Tycho response: 

Interactive shell script is started.

oscctrlstat

This command displays the current settings for the oscillator control parameters.  These parameters 

are used to discipline the oscillator.  The command formats the data and prints this fixed-length string 

having these fields:

  Oscctrlstat = LKSTAT COAST ESTERR MEASERR TIMEDEV AGERATE TAU TEMP

Where:

LKSTAT   

is the GPS subsystem control status, either acquiring, locking or locked.

COAST   

is the number of seconds in coast mode (unlocked).

ESTERR   

is the estimated time error when in coast mode in seconds.

MEASERR 

is the last measured time offset while locked in seconds.

TIMEDEV 

is the time deviation (TDEV) of measurements in seconds.

AGERATE 

is the regression computed oscillator ageing rate per day (several hour delay  

   

 

before the first measurements are displayed.).

TAU 

 

is the oscillator control loop averaging time constant in seconds.

TEMP 

 

is the internal temperature in °C for OCXO and Rubidium oscillators only.

  Query:   

 

 

oscctrlstat

  RTM3204/Tycho response: 

 

Oscctrlstat = LKD  0 2.72e-09 -2.72e-09 1.23e-09 -0.00e+00   235.2  53.500

Summary of Contents for RTM3204



































































Reviews: