background image

R T M 3 2 0 4   G P S   T i m i n g   M o d u l e   U s e r   M a n u a l

18

C H A P T E R   T H R E E

19

R T M 3 2 0 4   G P S   T i m i n g   M o d u l e   U s e r   M a n u a l

C O N T R O L   A N D   S T A T U S   C O M M A N D S

netconfig

Interactive shell script that allows the user to configure the IP 

network subsystem of the RTM3204/Tycho.

oscctrlstat

Prints the oscillator disciplining parameters.

pluginopts

Prints the board type and settings for any installed plug-in op-

tion board.

pluginoptsconfig

An interactive script that allows the user to change the settings 

on any configurable plug-in option board.

setgpscaldelay

An interactive script that allows the user to change the clock 

calibration delay.

setgpsdynmode

Allows the user to set the dynamic mode of operation of the 

GPS subsystem.  It may be ON or OFF.

setgpsrefpos

Interactive shell script that prompts the user for an accurate 

reference position, performs syntax and argument validity 

checking then passes the position to the GPS subsystem.

updaterootflag

Command to update the flag stored in FLASH that is read by 

the Linux bootloader at boot time to select operation with either 

the FACTORY or UPGRADE root file system.

upgradegps

Shell script that facilitates the GPS subsystem firmware up-

grade process.

 

Detailed Command 

 

Descriptions

accessconfig

This command starts an interactive shell script that will allow the root user to configure limitation of 

telnet

ssh

 and 

snmp

 access to the RTM3204.  By default, the unit is configured to allow access by 

all users.  If you need to limit 

telnet

ssh

 or 

snmp

 access, e.g. for security reasons, you must run 

this script as root from either the RS-232 serial I/O port or from a

 telnet

 or

 ssh

 session.

This script modifies these files:  

/etc/hosts.allow

 and 

/etc/hosts.deny

.  These are non-volatilely stored 

in the FLASH disk 

/boot/etc

 directory.  You must re-boot the RTM3204 after running this script for 

the changes to take effect. 

  Set: 

 

 

 

accessconfig

  RTM3204/Tycho response: 

Interactive shell script is started.

cpuopts

This command displays the current settings for the installed CPU Module outputs.

  Query:   

 

 

cpuopts

  RTM3204/Tycho response: 

CPU Option 1PPS is installed.

   

 

 

 

Current setting = 20 microseconds.

   

 

 

 

CPU Option TIME CODE is installed.

   

 

 

 

Current Setting = IRIG-B122.

cpuoptsconfig

This command starts an interactive shell script that will allow the root user to change the settings of 

any installed CPU Module output.  The user-selectable outputs are 1PPS, AM Code, and the optional 

Prog TTL and Synthesizer.

Summary of Contents for RTM3204



































































Reviews: