Endress+Hauser Proline Promag 55 Operating Manual Download Page 30

Page: 30 / 130

5 Block USER INTERFACE

Device Functions Proline Promag 55 FOUNDATION Fieldbus

Hauser

FORMAT
(2422)

Note!

This function is not available unless a number was selected in the ASSIGN function
(2420).

Use this function to define the maximum number of places after the decimal point for the
second value displayed in the additional line.

Options:

XXXXX. - XXXX.X - XXX.XX - XX.XXX -X.XXXX

Factory setting:

X.XXXX

Note!

• Note that this setting only affects the reading as it appears on the display, it has no

influence on the accuracy of the system's calculations.

• The places after the decimal point as computed by the measuring device cannot always

be displayed, depending on this setting and the engineering unit. In these instances an
arrow appears on the display between the measured value and the engineering unit
(e.g. 1.2

→

kg/h), indicating that the measuring system is computing with more

decimal places than can be shown on the display.

DISPLAY MODE
(2423)

Note!

This function is only available if VOLUME FLOW BARGRAPH IN % or MASS FLOW
BARGRAPH IN % was selected in the function ASSIGN (2420).

Use this function to define the format of the bar graph.

Options:

STANDARD (Simple bar graph with 25 / 50 / 75% gradations and integrated sign).

A0001258

SYMMETRY (Symmetrical bar graph for positive and negative directions of flow, with
–50 / 0 / +50% gradations and integrated sign).

A0001259

Factory setting:

STANDARD

Function description

USER INTERFACE

→

ADDITIONAL LINE

→

MULTIPLEX

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands