Endress+Hauser Proline Promag 55 Operating Manual Download Page 20

Page: 20 / 130

5 Block USER INTERFACE

Device Functions Proline Promag 55 FOUNDATION Fieldbus

Hauser

5.1

Group CONTROL

5.1.1

Function group BASIC CONFIGURATION

USER INTERFACE

⇒

CONTROL

CAA

⇒

BASIC CONFIGURATION 200

Function description

USER INTERFACE

→

CONTROL

→

BASIC CONFIGURATION

LANGUAGE
(2000)

Use this function to select the language for all texts, parameters and messages shown on
the local display.

Note!

The displayed options depend on the available language group shown in the LANGUAGE
GROUP (8226) function.

OPTIONS:

Language group WEST EU / USA:
ENGLISH
DEUTSCH
FRANCAIS
ESPANOL
ITALIANO
NEDERLANDS
PORTUGUESE

Language group EAST EU / SCAND:
ENGLISH
NORSK
SVENSKA
SUOMI
POLISH
RUSSIAN
CZECH

Language group ASIA:
ENGLISH
BAHASA INDONESIA
JAPANESE (syllabary)

Language group CHINA:
ENGLISH
CHINESE

Factory setting:

Country dependent

→

Page 123

Note!

• If you press the

key combination at startup, the language defaults to ENGLISH.

• You can change the language group via the configuration program ToF Tool - Fieldtool

Package. Please do not hesitate to contact your Hauser sales office if you have
any questions.

DISPLAY DAMPING
(2002)

Use this function to enter a time constant defining how the display reacts to severely
fluctuating flow variables, either very quickly (enter a low time constant) or with
damping (enter a high time constant).

User input:

0 to 100 seconds

Factory setting:

1 s

Note!

Setting the time constant to zero seconds switches off damping.

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands