Endress+Hauser Proline Promag 300 Description Of Device Parameters Download Page 156

Page: 156 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

156

Hauser

3.6.3

"Modbus data map" submenu

Navigation



Expert → Communication → Modbus data map

‣

Modbus data map

Scan list reg.0 to 15 (7114)

→  156

Scan list reg.0 to 15



Navigation

 Expert → Communication → Modbus data map → Scan list reg.0 to 15 (7114)

Description

Use this function to enter the scan list register. By entering the register address (1-based),

up to 16 device parameters can be grouped by assigning them to the scan list registers 0 to

15. The data of the device parameters assigned here are read out via the register addresses

5051 to 5081.

User entry

1 to 65

535

Factory setting

3.6.4

"Web server" submenu

Navigation

 Expert → Communication → Web server

‣

Web server

Webserv.language (7221)

MAC Address (7214)

DHCP client (7212)

IP address (7209)

Subnet mask (7211)

Default gateway (7210)

→  158

Webserver funct. (7222)

→  159

Summary of Contents for Proline Promag 300

















































































































































































































































































Search results

Summary of Contents for Proline Promag 300

Reviews:

Brands by name

Popular brands

Endress+Hauser Proline Promag 300, Description Of Device Parameters

Search results

Summary of Contents for Proline Promag 300

Reviews:

Brands by name

Popular brands