manualshive.com logo in svg

Endress+Hauser Proline Promag 300, Description Of Device Parameters

Share
Download
Endress+Hauser Proline Promag 300 Description Of Device Parameters Download Page 158

Description of device parameters

Proline Promag 300 Modbus RS485

158

Hauser

Selection

• Off

• On

Factory setting

Off

Additional information

Result

If the DHCP client functionality of the Web server is activated, the IP address (→   158),

Subnet mask (→   158) and Default gateway (→   158) are set automatically.

Identification is via the MAC address of the measuring device.

IP address

Navigation

 Expert → Communication → Web server → IP address (7209)

Description

Displays the IP address of the device's web server.

User entry

4 octet: 0 to 255 (in the particular octet)

Factory setting

192.168.1.212

Subnet mask

Navigation

 Expert → Communication → Web server → Subnet mask (7211)

Description

Displays the subnet mask.

User entry

4 octet: 0 to 255 (in the particular octet)

Factory setting

255.255.255.0

Default gateway

Navigation

 Expert → Communication → Web server → Default gateway (7210)

Description

Displays the default gateway.

User entry

4 octet: 0 to 255 (in the particular octet)

Factory setting

0.0.0.0

Summary of Contents for Proline Promag 300

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands