Endress+Hauser Nivocompact FTC 131 Technical Information Download Page 12

Page: 12 / 16

Housing Versions

Cable Gland

Housing IP 55: standard PG in
nickel-plated brass with NBR seal for
cable diameter 7

…

10 mm.

Housing IP 66: Water-tight PG in
polyamide with Neoprene-CR seal for
cable diameter 5

…

12 mm.

Electronic Inserts

Terminal connections: for max. 2.5 mm

Measuring frequency:
approx. 750 kHz for short probes,
up to 4 m, switchable to approx.
450 kHz for long probes

Initial capacitance, adjustable:
to approx. 400 pF

Switching delay: approx. 0.5 s

Minimum/Maximum Fail-Safe Switching:
selectable with rotary switch

Switching indication: red LED

Electronic Insert EC 20
for AC voltage
(Two-wire Connection)

Power supply U

∼

21 V

…

250 V, 50/60 Hz

Connected loads, short-term
(max. 40 ms): max. 1.5 A;
max. 375 VA with 250 V;
max. 36 VA with 24 V

Maximum voltage drop: 11 V

Connected loads, continuous:
max. 350 mA;
max. 87 VA with 250 V;
max. 8.4 VA with 24 V

Minimum load current with 250 V:
10 mA (2.5 VA)

Minimum load current with 24 V:
20 mA (0.5 VA)

Residual current (eff.): < 5 mA

Electronic Inserts EC 22 and EC 23
for DC Voltage
(Three-wire connection)

Power supply U =: 10 V...55 V

Superimposed AC voltage U

max. 5 V

Current consumption: max. 15 mA

Load connection: Open Collector;
PNP (EC 22) or NPN (EC 23)

Switching voltage: max. 55 V

Connected load, short-term
(max. 1 s): max. 1 A

Connected load, continuous:
max. 350 mA

Protected against reverse polarity

Electronic Insert EC 24
for DC and AC Voltages
(Relay Output)

Power supply U =: 20 V

…

200 V

or power supply U

∼

21 V

…

250 V, 50/60 Hz

Current consumption (eff.): max. 5 mA

Peak inrush current:
max. 200 mA, max. 5 ms

Pulse current: max. 50 mA, max. 5 ms

Pulse frequency: approx. 1.5 s

Output:
potential-free change-over contact

Contact load capacity:
U

∼

max. 250 V, I

∼

max. 6 A,

∼

max. 1500 VA (cos

= 1) or

∼

max. 750 VA, cos

ϕ ≥

0.7

U = max. 250 V, I = max. 6 A,
P = max. 200 W

Operating life: min. 10

switchings

at max. contact load

Additional switching delay:
max. 1.5 s

Subject to modification

A
Aluminium housing with
standard cable gland
PG 16,
Protection IP 55

B
Aluminium housing with
water-tight cable gland
PG 16,
Protection IP 66

R
Aluminium housing with
synthetic coating, for
aggressive
atmospheres;
with water-tight cable
gland PG 16,
Protection IP 66

K
Synthetic housing in
PBTP with water-tight
cable gland PG 16,
Protection IP 66

Summary of Contents for Nivocompact FTC 131

















Search results

Summary of Contents for Nivocompact FTC 131

Reviews:

Related manuals for Nivocompact FTC 131

Brands by name

Popular brands

Endress+Hauser Nivocompact FTC 131, Technical Information

Search results

Summary of Contents for Nivocompact FTC 131

Reviews:

Related manuals for Nivocompact FTC 131

Brands by name

Popular brands