Endress+Hauser MMP20 SONO Mobil HD2 Operating Instructions Manual Download Page 11

Page: 11 / 38

MMP20 SONO Mobil HD2 (option E)

Hauser

Page 11

Operation

Key function:

Key

Description

Measure

•

Switch on/off



press and hold for 1s

•

Take a measurement



press briefly

•

Select a menu item



press briefly

•

Save a setting



press briefly

Settings

•

Exit "Settings"

•

Switch to the menu

•

Go back from the menu items

•

Previous menu item or setting

•

For selection

–

material calibration (Single Value/

Average mode)

•

Access to density setting (Water Calculation mode)

Down

•

Next menu item or setting

•

Clear the value memory (Average mode)

Symbols on the display:

Symbol

Description

Remaining battery

Measurement active

Setting saved

Brightness of background lighting

Time until switchoff (lighting / APO)

Press the "Up" key

Press the "Down" key

Summary of Contents for MMP20 SONO Mobil HD2







































Search results

Summary of Contents for MMP20 SONO Mobil HD2

Reviews:

Related manuals for MMP20 SONO Mobil HD2

Brands by name

Popular brands

Endress+Hauser MMP20 SONO Mobil HD2, Operating Instructions Manual

Search results

Summary of Contents for MMP20 SONO Mobil HD2

Reviews:

Related manuals for MMP20 SONO Mobil HD2

Brands by name

Popular brands