manualshive.com logo in svg

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 136 / 210

Share
Download
Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 136

Operation

Proline Promag P 500 HART

136

Hauser

11  

Operation

11.1   Reading the device locking status

Device active write protection: 

Locking status

 parameter

Operation → Locking status

Function scope of the "Locking status" parameter

Options

Description

None

The access status displayed in the 

Access status

 parameter applies →   75. Only

appears on local display.

Hardware locked

The DIP switch for hardware locking is activated on the PCB board. This locks write
access to the parameters (e.g. via local display or operating tool) .

SIL locked

The SIL mode is enabled. This locks write access to the parameters (e.g. via local
display or operating tool).

Temporarily locked

Write access to the parameters is temporarily locked on account of internal
processes running in the device (e.g. data upload/download, reset etc.). Once the
internal processing has been completed, the parameters can be changed once
again.

11.2   Adjusting the operating language

Detailed information:

• To configure the operating language →   94

• For information on the operating languages supported by the measuring device

→   195

11.3   Configuring the display

Detailed information:

• On the basic settings for the local display →   109

• On the advanced settings for the local display →   121

11.4   Reading measured values

With the 

Measured values

 submenu, it is possible to read all the measured values.

11.4.1   "Process variables" submenu

The 

Process variables

 submenu contains all the parameters needed to display the current

measured values for each process variable.

Navigation

"Diagnostics" menu → Measured values → Process variables

‣

Process variables

Volume flow

→   137

Mass flow

→   137

Summary of Contents for Hart Proline Promag P 500



















































































































































































































Reviews:

No comments