manualshive.com logo in svg

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 195 / 210

Share
Download
Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 195

Proline Promag P 500 HART

Technical data

Hauser

195

External WLAN antenna

• Antenna: ASA plastic (acrylic ester-styrene-acrylonitrile) and nickel-plated brass

• Adapter: Stainless steel and nickel-plated brass

• Cable: Polyethylene

• Plug: Nickel-plated brass

• Angle bracket: Stainless steel

Ground disks

Stainless steel, 1.4435 (F316L); Alloy C22, 2.4602 (UNS N06022); tantalum; titanium

Fitted electrodes

Measuring electrodes, reference electrodes and electrodes for empty pipe detection:

• Standard: stainless steel, 1.4435 (F316L); Alloy C22, 2.4602 (UNS N06022); tantalum,

titanium

• Optional: only platinum measuring electrodes

Surface roughness

Stainless steel electrodes, 1.4435 (F316L); Alloy C22, 2.4602 (UNS N06022); platinum;

tantalum; titanium:

≤ 0.3 to 0.5 µm (11.8 to 19.7 µin)

(All data relate to parts in contact with fluid)
Liner with PFA:

≤ 0.4 µm (15.7 µin)

(All data relate to parts in contact with fluid)

16.11   Operability

Languages

Can be operated in the following languages:

• Via local operation

English, German, French, Spanish, Italian, Dutch, Portuguese, Polish, Russian, Turkish,

Chinese, Japanese, Korean, Bahasa (Indonesian), Vietnamese, Czech, Swedish

• Via Web browser

English, German, French, Spanish, Italian, Dutch, Portuguese, Polish, Russian, Turkish,

Chinese, Japanese, Korean, Bahasa (Indonesian), Vietnamese, Czech, Swedish

• Via "FieldCare", "DeviceCare" operating tool: English, German, French, Spanish, Italian,

Chinese, Japanese

Local operation

Via display module

Two display modules are available:

• Order code for "Display; operation", option 

F

 "4-line, illuminated, graphic display; touch

control"

• Order code for "Display; operation", option 

G

 "4-line, illuminated, graphic display; touch

c WLAN"

Information about WLAN interface →   84

Summary of Contents for Hart Proline Promag P 500



















































































































































































































Reviews:

No comments