manualshive.com logo in svg

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 84 / 210

Share
Download
Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 84

Operation options

Proline Promag P 500 HART

84

Hauser

Service interface

Via service interface (CDI-RJ45)

A point-to-point connection can be established to configure the device onsite. With the

housing open, the connection is established directly via the service interface (CDI-RJ45) of

the device.

An adapter for RJ45 and the M12 connector is optionally available:

Order code for "Accessories", option 

NB

: "Adapter RJ45 M12 (service interface)"

The adapter connects the service interface (CDI-RJ45) to an M12 connector mounted

in the cable entry. Therefore the connection to the service interface can be established

via an M12 connector without opening the device.

Proline 500 – digital transmitter

open

press

1

2

3

  A0029163

 40

Connection via service interface (CDI-RJ45)

1

Computer with Web browser (e.g. Microsoft Internet Explorer, Microsoft Edge) for accessing the integrated
device Web server or with "FieldCare", "DeviceCare" operating tool with COM DTM "CDI Communication TCP/IP"

2

Standard Ethernet connecting cable with RJ45 connector

3

Service interface (CDI-RJ45) of the measuring device with access to the integrated Web server

Proline 500 transmitter

2

3

1

  A0027563

 41

Connection via service interface (CDI-RJ45)

1

Computer with Web browser (e.g. Microsoft Internet Explorer, Microsoft Edge) for accessing the integrated
device Web server or with "FieldCare", "DeviceCare" operating tool with COM DTM "CDI Communication TCP/IP"

2

Standard Ethernet connecting cable with RJ45 connector

3

Service interface (CDI-RJ45) of the measuring device with access to the integrated Web server

Via WLAN interface

The optional WLAN interface is available on the following device version:

Order code for "Display; operation", option 

G

 "4-line, illuminated, graphic display; touch

c WLAN"

Summary of Contents for Hart Proline Promag P 500



















































































































































































































Reviews:

No comments