background image

Basic safety instructions

FieldPort SWA50

8

Hauser

2  

Basic safety instructions

2.1  

Requirements for personnel

The personnel for installation, commissioning, diagnostics and maintenance must meet

the following requirements:

Trained, qualified specialists: must have a relevant qualification for this specific role

and task and have been trained by Hauser. Experts at the Hauser

service organization.

Personnel must be authorized by the plant owner/operator.

Personnel must be familiar with regional and national regulations.

Before starting work: personnel must read and understand the instructions in the

manual and supplementary documentation as well as the certificates (depending on

the application).

Personnel must follow instructions and comply with general policies.

Operating personnel must meet the following requirements:

Personnel are instructed and authorized according to the requirements of the task by

the facility's owner-operator.

Personnel follow the instructions in this manual.

2.2  

Designated use

The FieldPort SWA50 is a loop-powered adapter that converts the HART signal of the

connected HART field device into a reliable and encrypted WirelessHART signal. The

FieldPort SWA50 can be retrofitted to all 2-wire or 4-wire HART field devices.
The Bluetooth signal may not be used to replace the wiring in the case of safety

applications with a control function.

Incorrect use

Non-designated use can compromise safety. The manufacturer is not liable for damage

caused by improper or non-designated use.

2.3  

Workplace safety

For work on and with the device:

Wear the required personal protective equipment according to federal/national

regulations.

2.4  

Operational safety

Risk of injury!

Operate the device only if it is in proper technical condition, free from errors and faults.

The operator is responsible for interference-free operation of the device.

Modifications to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers:

If modifications are nevertheless required, consult with Hauser.

Summary of Contents for FieldPort SWA50













































































Reviews: