Endress+Hauser Cerabar PMC11 Technical Information Download Page 5

Page: 5 / 52

Cerabar PMC11, PMC21, PMP11, PMP21

Hauser

Documentation

The document types listed are available:

In the Download Area of the Hauser Internet site: www.endress.com → Download

Brief Operating Instructions (KA): getting the 1st measured value quickly

These instructions contain all the essential information from incoming acceptance to initial

commissioning.

Operating Instructions (BA): your comprehensive reference

These Operating Instructions contain all the information that is required in various phases of the life

cycle of the device: from product identification, incoming acceptance and storage, to mounting,

connection, operation and commissioning through to troubleshooting, maintenance and disposal.

Safety Instructions (XA)

Depending on the approval, the following Safety Instructions (XA) are supplied with the device. They

are an integral part of the Operating Instructions.

Device

Directive

Documentation

Option

PMP21

ATEX II 1/2G Ex ia IIC T4 Ga/Gb

XA01271P

PMC21

ATEX II 2G Ex ia IIC T4 Gb

XA01271P

PMC21
PMP21

ATEX II 3G Ex ec IIC T4 Gc

XA01533P

PMC21
PMP21

FM IS Cl. I, Div.1 Gr. A-D T4

XA01321P

PMC21
PMP21

CSA C/US IS Cl. I Div. 1 Gr. A-D

XA01322P

PMC21
PMP21

EAC Ex ia IIC T4 Ga/Gb

XA01540P

PMC21
PMP21

IEC Ex ia IIC T4 Ga/Gb

XA01271P

PMC21
PMP21

NEPSI Ex ia IIC T4

XA01363P

PMC21
PMP21

TIIS Ex ia IIC T4

In preparation

Product Configurator order code for "Approval"

The nameplate indicates the Safety Instructions (XA) that are relevant to the device.

Summary of Contents for Cerabar PMC11





















































Search results

Summary of Contents for Cerabar PMC11

Reviews:

Related manuals for Cerabar PMC11

Brands by name

Popular brands

Endress+Hauser Cerabar PMC11, Technical Information

Search results

Summary of Contents for Cerabar PMC11

Reviews:

Related manuals for Cerabar PMC11

Brands by name

Popular brands