Endress+Hauser 9P5B Functional Safety Manual Download Page 40

Page: 40 / 44

Appendix

Proline Prosonic Flow P 500 HART

Hauser

‣

Modifications to devices with SIL capability onsite at the user's plant are possible following

approval by the Hauser manufacturing center. In this case, the modifications must

be performed and documented by an Hauser service technician.

‣

Modifications to devices with SIL capability by the user are not permitted.

6.8

Decommissioning

For detailed information on decommissioning, see the Operating Instructions for the

device

Appendix

7.1

Structure of the measuring system

7.1.1

System components

A0015443

 5

System components

Pump

Measuring device

Valve

Automation system

An analog signal (4–20 mA) proportional to the volume flow is generated in the transmitter.

This is sent to a downstream automation system where it is monitored to determine whether

it falls below or exceeds a specified limit value. The safety function (volume flow monitoring)

is implemented in this way.

Summary of Contents for 9P5B













































Search results

Summary of Contents for 9P5B

Reviews:

Related manuals for 9P5B

Brands by name

Popular brands

Endress+Hauser 9P5B, Functional Safety Manual

Search results

Summary of Contents for 9P5B

Reviews:

Related manuals for 9P5B

Brands by name

Popular brands