results in
5-step long
infinitely repeating
trigger sequence:
OPERATING MODES
1.1 Recording the trigger sequence in step mode:
LED light up
RED
in standard step recording mode
if track selector is switched to the right or to the left
1.0 Step a.k.a. 'standard' mode
2.0 Euclidean mode
Record a trigger sequence to track I or II
using STEP and REST buttons
Switching the
track select to the
middle
first step of recorded
5-steps sequence
...
last step of
recorded sequence
buttons pressed 5 times in total
the recorded sequence will fire triggers
on 1
st
, 2
nd
and 4
th
step
repeating the
same sequence
again repeating the same
sequence of triggers
and so on
x1
x1
x1
x1
x1
1.2 Repeats in step mode
x1
x2
...
Record a simple 3 step trigger sequence
1 2 3 4 5
1 2 3
with REPEATS I knob set to 0:
Adjusting REPEATS amount will add 0-7 trigger repeats after an active step in the sequence, thus increasing the total sequence length:
1 2 3 4
...
1
0
original first trigger
repeated trigger
empty steps (rests) of the sequence
repeated same sequence
...
2
original first trigger
x2 times repeated trigger
empty steps (rests) of the sequence
repeated same sequence
again same
repeating sequence, etc.
1 2 3 4 5
With CV applied we can
dynamially change
amount of repeats
2 sec
2 sec
Holding STEP (for track 1) or REST (for track 2) button for 2 seconds will enable (or disable) Euclidean mode:
2.1. Recording the sequence length in Euclidean mode:
Switch to the left to check if track I is in Euclidean mode or switch to the right to check if track II is in Euclidean mode.
LED lighs up
FUCHSIA
LED lighs up
FUCHSIA
x1
x1
each single press adds
+1 step to the Euclidean circle
each single press adds
+16 steps to the Euclidean circle
switching to the center,
saves the steps amount
step 1
step 2
step 3
step 4
step 5
step 6
step 7
step 8
step 9
step 10
step 11
step 12
step 13
step 14
step 15
step 16
Euclidean circle with default
count of 16 steps
with REPEATS knob we set
the number of fills (active
steps equally distanced
within the euclidean circle)
With CV applied we can
dynamially change
the amount of fills
0
no
triggers
1
1
trigger
2
2
triggers
3
3
triggers
4
4
triggers
etc.
...
3. Live mode
Short press on STEP or REST
buttons will mute/unmute trigger
outputs on either Track I or II
In live mode both tracks
infinitely repeat their
trigger sequences.
4. Clock divider
With external clock applied, the
divider is set with rate/div knob
to be applied to trigger repeats
or Euclidean circle speed;
middle knob position (x1)
doesn't affect the clock divider.
6. Syncronization
In TUPLET mode (div knob fully CCW)
the number of trigger
repeats is streched into one bar.
Some particular cases of using tuplets
are triplets and – if used creatively –
becomes ratcheting.
5.Tuplets
clock output in 16th notes after divider
(PPQN24÷6)
Triggers applied to reset I or II
reset the according trigger sequence to the first step.
Reset in I is normalled to reset in II.
I.e. a reset is applied to both tracks, if a signal
is sent to reset in I only and no cable is plugged
into reset in II.
7. Patterns
Each track has 8 patterns selected by pressing both the STEP and the REST button and rotating the REPEATS (I or II) knob
at the same time. Patterns can be combined and are selected separately for track I and II. Pattern sequences and
last patterns selected are recalled on next power cycle.
Track I or II
pattern 1
pattern 2
pattern 8
pattern 7
...
+
pattern 1
pattern 2
pattern 3
pattern 4
pattern 5
pattern 6
pattern 7
pattern 8
separate patten selection
for track I and track II
1 2
1 2 3 4 5
1 2 3 4 5
1 2 3
1 2 3
1 2
1 2 3 4
1 2
1 2 3 4 5
1 2 3 4 5
1 2
In this mode we set the length of the Euclidean
circle (by default 16 steps) and set the amount
of trigger FILLS with REPEATS knob or its CV.
again same
repeating sequence, etc.
© Endorphin.es® 2011–2021
