background image

 

ENANCER Electrónica S.A.

 

 

Page 2 of 17

 

Rua Max Grundig 9 

 

 

 

4705-820 Braga Portugal                                                                                                                                             [email protected]                                                                                                                                                                                                            
Tel: +351 253 221 484                                                                                                                                                 www.only-smartbuildings.com 

Historial 

 

Version 

Date 

Author 

Changes  

1.0 

2011-11-16 

 

1.1 

2011-11-29 

 

Chapter troubleshooting added 

1.2 

2015-05-13 

 

Minor changes 

1.3 

2018-09-13 

 

Branding actualization 

 

Index  

 

Historical ........................................................................................................................ Erro! Marcador não definido.

 

Index .......................................................................................................................................................................... 2

 

Introduction ................................................................................................................................................................ 3

 

ONLY Automation system ......................................................................................................................................... 3

 

Electrical piping and threading .................................................................................................................................. 3

 

Protections ................................................................................................................................................................. 5

 

Switchboards ............................................................................................................................................................. 6

 

Single phase supplies with ONLY 1 switchboard ...................................................................................................... 7

 

Single phase installations with more than one switchboard ...................................................................................... 8

 

Three-phase installations with more than one switch board ..................................................................................... 9

 

BUS Line .................................................................................................................................................................. 12

 

Connection Schemes .............................................................................................................................................. 13

 

Configuration ........................................................................................................................................................... 15

 

Measuring and Troubleshooting .............................................................................................................................. 17

 

 

Summary of Contents for ONLY


















Reviews: