background image

maintenance, service operations or adjustments can be performed the
GBIC.

Small Form Factor Transceiver

The small form factor transceiver is an integrated duplex data link for
bi−directional communications over multimode or single mode optical
fiber. Each small form factor transceiver consists of a transmitter and
receiver optical subassembly. The transmitter subassembly contains a
semiconductor laser emitting in the wavelength range of 770 to 860
nanometers for shortwave length small form factor transceivers and 1270
to 1355 nanometers for long wavelength small form factor transceivers.
For non−OFC links, the optical power from the laser transmitter is
controlled and maintained at a lower power level. The power emitted
from either an open fiber or open laser transmitter is guaranteed to be
below the Class 1 limit. Class 1 laser products are not considered
hazardous. No user maintenance, service operations or adjustments can
be performed the small form factor transceiver.

1x9 Transceiver

The 1x9 transceivers is an integrated duplex data link for bi−directional
communications over multimode fiber. Each 1x9 consists of a transmitter
and receiver optical subassembly. The transmitter subassembly contains
a semiconductor laser emitting in the wavelength range of 770 to 860
nanometers for shortwave 1x9s. For non−OFC links, the optical power
from the laser transmitter is controlled and maintained at a lower power
level. The power emitted from either an open fiber or open laser
transmitter is guaranteed to be below the Class 1 limit. Class 1 laser
products are not considered hazardous. No user maintenance, service
operations or adjustments can be performed the 1x9 transceiver.

Usage Restrictions

Failure to comply with these usage restrictions may result in incorrect operation
of the system and could possible lead to points of access that may emit laser
radiation levels above the Class 1 limits established in the U. S. by the DHHS
and within Europe by EN60825−1/EN60825−2.

GLM
GBIC
1 x 9 Transceiver
Small Form Factor Transceiver

Emulex Drivers, Software and Manuals

23

Summary of Contents for LP8000


























Reviews: