background image

Combined Boot User Manual

Page 23

 

Making a Bootable System Disk

The examples in this procedure use the logical drive designated as "c1t1d0" (controller 1, target 1, lun 
0). Your logical drive may be different.

1.

Boot from the local system disk.

2.

Run the format utility.

# format

3.

Select the logical drive to become the boot disk (in this case, c1t1d0).

4.

Select the partition option and partition the disk as desired.

5.

Select the label option and write a volume label to the target disk.

For help with the format utility, refer to the man page "man format".

6.

Install the boot on partition 0 of the target disk. (Enter this command as one line.)

# installboot /usr/platform/ `uname -i`/lib/fs/ufs/bootblk /dev/

rdsk/c1t1d0s0

7.

Create a filesystem for each partition that will contain a mounted filesystem.

# newfs -v /dev/rdsk/c1t1d0s0 

(will become root)

 

# newfs -v /dev/rdsk/c1t1d0s6 

(will become usr)

 

# newfs -v /dev/rdsk/c1t1d0s7 

(will become export/home)

8.

Create temporary mount points for the new partitions.

# mkdir root2

 

# mkdir usr2

 

# mkdir export2

Host_did

shows host DID number 

Enable_flag 

internal flag for OpenBoot 

Boot_id 

shows target ID number 

Lnk_timer

internal use for OpenBoot 

Plogi_timer

internal use for OpenBoot

LUN 

shows boot LUN in use

DID 

shows boot ID in use 

WWPN 

shows boot WWPN in use

Note: 

Target ID can be bound to either DID (destination ID) or WWPN (worldwide port 

name) and saved in an adapter nvram. It can also be saved in an environmental 
variable boot-device. 

Table 1: Signature Table (Continued)

Signature OpenBoot 

signature

Summary of Contents for Combined Boot 5.01a0































Reviews: