EMS EMS827 User Manual Download Page 9

Page: 9 / 60

EMS 827

GENSET CONTROLLER

Confidential

www.ems.gen.nz

Page 9

Function

Description

Auto Mode

Green LED indication that the unit is in Automatic Start Mode

Test Mode

Green LED indication that the unit is in Test Mode

4.6

Transfer Control LED Indications

Function

Description

Alternator

Phase

Available

Red LED indication that the Alternator phase 1 voltage is available.

Alternator

Phase

Available

Yellow LED indication that the Alternator phase 2 voltage is
available.

Alternator

Phase

Available

Blue LED indication that the Alternator phase 3 voltage is available.

Alternator Available

Green LED indication that the Alternator is available for the load.

Alternator on Load

Green LED indication that the Alternator is on load.

Mains

Phase

Available

Red LED indication that the mains phase 1 voltage is available.

Mains

Phase

Available

Yellow LED indication that the mains phase 2 voltage is available.

Mains

Phase

Available

Blue LED indication that the mains phase 3 voltage is available.

Mains AC Available

Green LED indication that the mains is available for load.

Mains AC on Load

Green LED indication that the mains is on load.

4.7

System LCD Displays

Function

Description

Setup menu

System configuration menus

Start Up

Clear step-by-step start up sequencing messages

Shutdown

Clear step-by-step shutdown sequencing messages

Transfer

Clear step-by-step load transfer messages

Summary of Contents for EMS827





























































Search results

Summary of Contents for EMS827

Reviews:

Related manuals for EMS827

Brands by name

Popular brands

EMS EMS827, User Manual

Search results

Summary of Contents for EMS827

Reviews:

Related manuals for EMS827

Brands by name

Popular brands