background image

37134-4-0319

Page 13

1.   SToP!

   Read the safety information above.

2.  Turn off all electric power to the appliance.

3.   This appliance is equipped with an ignition device which 

automatically lights the pilot.  Do not try to light the pilot 

by hand.

ON

OFF

IGNITOR

CONTROL

GAS FLOW

GAS VALVE SHOWN IN OFF POSITION

HONEYWELL IP SMART VALVE

4.  Remove front panel door.

5.   Slide  gas control switch to "oFF."
6.   Wait ten (10) minutes   to clear out any gas.  Then smell 

for gas, including near the floor.  If you smell gas, SToP! 

Follow "B" in the safety information above.  If you don't 

smell gas, go to the next step.

7.  Slide gas control switch to "oN".
8.   replace front panel  door. 
9.   Turn on all electric power to the appliance.
10.  If the appliance will not operate, follow the instructions 

"To TURn oFF GAS To APPLIAnCE" and  call your service 

technician or gas supplier.

A.   This appliance is equipped with an ignition device which 

automatically lights the pilot.  

 Do not try to light the pilot by hand.
B.   BEForE oPErATING  smell all around the appliance area 

for gas.  Be sure to smell next to the floor because some 

gas is heavier than air and will settle on the floor.

 

WHAT To Do IF You SMEll GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; 

 

do not use any phone in your building.

•  Immediately call your gas supplier from a neighbor's 

phone.  Follow the gas supplier's instructions.

•  If you cannot reach your gas supplier, call the fire 

department.

C.   Use only your hand to slide the gas control knob.  never 

use tools. Force or attempted repair may result in a fire 

or explosion.

D.   Do not use this appliance if any part has been under water.  

Immediately call a qualified service technician to inspect 

the appliance and to replace any part of the control system 

and any gas control which has been under water.

INTErMITTENT PIloT (IP) -lIGHTING INSTrucTIoNS

For Your SAFETY rEAD BEForE oPErATING

oPErATING INSTrucTIoNS

1.   Turn off all electric power to the appliance if service is to 

be performed.

2.   Remove front panel door.

3.   Slide gas control switch to "oFF." 
4.   replace front panel door.

To TurN oFF GAS To APPlIANcE

WArNING 

If you do not follow these instructions exactly, a fire or explosion may result causing property damage, 

personal injury or loss of life.

Summary of Contents for FAW40IPXLP-1





















Reviews: