manualshive.com logo in svg

Empire Heating Systems DV-55T-1, Installation Instructions And Owner'S Manual

Share
Download
Empire Heating Systems DV-55T-1 Installation Instructions And Owner'S Manual Download Page 2

13118-7-0408

Page 2

SECTION 

PAGE

Important Safety Information ......................................................................................................................3
Vent Kit Information ....................................................................................................................................3
Safety Information for Users of LP Gas ......................................................................................................4
Requirements for Massachusetts ..................................................................................................................5
Introduction ..................................................................................................................................................6
Specifications ...............................................................................................................................................6
Gas Supply ............................................................................................................................................... 7-8
Clearances  ...................................................................................................................................................8
Installation Instructions .......................................................................................................................... 9-11
Lighting Instructions  .................................................................................................................................12
Pilot Flame Characteristics  .......................................................................................................................13
Main Burner Flame Characteristics  ..........................................................................................................13
Wiring ........................................................................................................................................................14
Service and Maintenance Suggestions .......................................................................................................15
How to Order Repair Parts .........................................................................................................................16
Parts List  ...................................................................................................................................................16
Parts View ..................................................................................................................................................17
Service Notes ....................................................................................................................................... 18-19

TABLE OF CONTENTS

Summary of Contents for DV-55T-1





















Reviews:

No comments

Brands by name

Popular brands

Load more brands