background image

Page 1

VFHS-20/10

INSTALLATION  INSTRUCTIONS

AND

OWNER'S  MANUAL

UNVENTED

GAS FIREPLACE

MODELS

VFHS-20R-1

VFHS-20/10T-1

EFFECTIVE  DATE

MAY, 2001

WARNING:  If the information in
this manual is not followed exactly, a
fire or explosion may result causing
property damage, personal injury or
loss of life.

 — Do not store or use gasoline or other

flammable vapors and liquids in the
vicinity of this or any other appliance.

 — WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electrical switch;
do not use any phone in your build-
ing.

Immediately call your gas supplier
from a neighbor's phone.  Follow
the gas supplier's instructions.

If you cannot reach your gas sup-
plier, call the fire department.

 — Installation and service must be per-

formed by a qualified installer, service
agency or the gas supplier.

This is an unvented gas-fired heater.  It
uses air (oxygen) from the room in which
it is installed. Provisions for adequate com-
bustion and ventilation air must be pro-
vided. Refer to page 6.

WARNING: If not installed, operated and
maintained in accordance with the manu-
facturer's instructions, this product could
expose you to substances in fuel or from
fuel combustion which can cause death or
serious illness.

WATER VAPOR:  A BY-PRODUCT OF
UNVENTED ROOM HEATERS
Water vapor is a by-product of gas
combustion. An unvented room heater
produces approximately one (1) ounce
(30ml) of water for every 1,000 BTU's
(.3KW's) of gas input per hour. Refer to
page 6.

R-5703

Summary of Contents for VFHS-10T-1





























Reviews: