![background image](http://html1.mh-extra.com/html/empire-comfort-systems/millivolt-dvcd32fp30/millivolt-dvcd32fp30_installation-instructions-manual_2403944003.webp)
38712-2-0719
Page 3
Samples and Definitions:
danger
indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
Warning
indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
caUtion
indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
NOTICE:
Addresses practices not related to personal injury.
Read all instructions before starting installation and follow them
carefully to insure safety. Failure to follow the instructions will
void the warranty and may cause a fire hazard.
The warranty will be voided by, and the warranter disclaims any
responsibility for the following actions:
•
Installation of any damaged fireplace or vent system
component.
•
modification for the fireplace or direct vent system.
•
Installation other than as instructed by empire Comfort
Systems.
•
Improper positioning of logs, glass door, or decorative
accessories.
•
Installation and/or use of any component part not
manufactured or approved by empire Comfort Systems.
All correspondence should refer to complete model Number,
Serial Number and type of gas. Fill out the Homeowner
Reference Section on page 5.
television considerations
Installing a television above a fireplace has become increasingly
popular; however, the area above any fireplace gets hot and most
TV manufacturers recommend against placing their products
near a heat source.
If you install a television above this fireplace, empire Comfort
Systems accepts no responsibility for damage or injuries. Follow
the television manufacturer’s installation instructions, including
any recommendations regarding proximity to heat sources.
If you have a TV above your fireplace, turn off the fireplace and
let it cool completely before servicing or touching any buttons on
the TV.
1. Determine where to install the fireplace. See page 11.
2. Frame the opening. See pages 14 - 15.
3. Install the fireplace. See page 15.
4. Install the venting. See pages 17 - 27.
5. Install and connect the gas lines. See pages 12 - 13.
6. Install the wiring. See pages 14, 70 and 74.
7. Light the fireplace. See pages 71 and 75.
8. Troubleshoot issues. See pages 72 and 76 - 78.
9. Place the serial number sticker located in the instruction
envelope onto the
“
Homeowner Reference Information
”
page.
before YoU start
10. Show the homeowner where the rating plate and lighting
instruction plate are located.
see figure 1.
11. Show the homeowner how to operate the fireplace.
12. Show the homeowner how to do the basic maintenance.
13. Read the safety information pages 92 - 94.
14. If located in the Commonwealth of massachusetts, note the
special requirements on page 95.
Unpacking the fireplace
1. Cut binding straps and shrink wrap.
2. Remove the top of the carton.
3. Carefully remove the carton contents.
4. Use the Carton Contents and Hardware Pack lists on page 4
to verify all components are present.
5. Verify that the fireplace and components have not been
damaged during shipping.
6. Set fireplace in a location near to its final installation location.
preparation
This fireplace and its components are safe when installed in
accordance with this Installation manual. Report any parts
damaged in shipment to your dealer. Do not install the fireplace
with damaged, incomplete or substitute parts.
Installation Considerations
•
Gas supply piping – right or left side entrance
•
electrical supply and connections – for optional fan kit
•
120V, 60Hz, 1 Amp
•
Right side entrance
•
Allowable fireplace mounting surfaces:
•
A flat, hard, combustible or non-combustible surface
•
A raised platform of combustible or non-combustible
material.
•
The four corners of the fireplace onto non-combustible
material so that contact is made on all four perimeter
edges on the bottom of the fireplace – such as on
cylinder blocks (where allowed by local codes).
•
If the fireplace is installed directly on carpeting, tile or other
combustible material other than wood flooring, it should be
installed on a metal or wood panel extending the full width
and depth of the fireplace.
•
This fireplace is designed to be installed in a zero-clearance
enclosure. Combustible material can come in contact with
the top and side standoff spacers, and the fireplace can be
secured to combustible framing with the framing brackets
provided with the fireplace.
VALVE
RATING
PLATE
LIGHTING
INSTRUCTION
PLATE
figure 1