manualshive.com logo in svg

Empire Comfort Systems DLCX36SP93N-1, Installation Instructions And Owner'S Manual, Page: 18 / 52

Share
Download
Empire Comfort Systems DLCX36SP93N-1 Installation Instructions And Owner'S Manual Download Page 18

29004-0-0711

Page 18

To Use the vent Graph (

Figure

 15)

1.  Determine the height of the center of the horizontal 

vent pipe. Using this dimension on the Sidewall Vent 

Graph, locate the point it intersects with the slanted 

graph line.

2.  From the point of this intersection, draw a vertical line 

to the bottom of the graph.

3.  Select the indicated dimension, and position the unit 

in accordance with same.

EXAMpLE  A:  (Top  vent  Connections  with  vertical 

Termination).

If the vertical dimension from the floor of the unit is 35 

feet, the horizontal run to the outer wall flange must not 

exceed 6.5 feet.

EXAMpLE  B:  (Top  vent  Connections  with  vertical 

Termination)

If the vertical dimension from the floor of the unit is 6.5 

feet, the horizontal run to the outer wall flange must not 

exceed 14.5 feet.

SpECIAL NOTE:

 For each 45 degree elbow installed in 

the horizontal run, the length of the horizontal run MUST 

be reduced by 18" (45cm). This does not apply if the 45 

degree elbows are installed on the vertical part of the vent 

system. Reduce 3' for every 90° elbow.

Example: 

According to the chart the maximum horizontal 

vent length is 20' and if two 45 degree elbows are required 

in the horizontal vent it must be reduced to 17'.
The  maximum  number  of  45  degree  elbows  permitted 

per side wall installation is two (2). These elbows can be 

installed in either the vertical or horizontal run.

Note:

 On vertical venting the first elbow is not counted.

Figure

 15

  Acceptable vertical and horizontal vent run.

 

Rigid Venting • 40' maximum vertical run 

 

                      • 20' maximum horizontal run

 

Flex Venting • 35' maximum vertical run

 

                      • 20' maximum horizontal run

  Unacceptable vertical and horizontal vent run.

venting Graph (Dimensions in Feet)

vENTING FIREpLACE - TOp

TOP EXIT - VERTICAL AND HORIZONTAL TERMINATION

(DIMENSIONS IN FEET)

NOTE: FLEX VENT

MAXIMUM HEIGHT

IS 35 FEET

VER

TICAL

DIMENSION FROM

THE BOTT

OM OF

THE UNIT

TO

THE CENTER OF

THE FLUE OUTLET

W

ITH VER

TICAL

OR HORIZONT

AL

TERMINA

TION CAPS

TOP VENT

CONNECTION

TOP VENT CONNECTION

OF VENTING WITH

HORIZONTAL TERMINATION

HORIZONTAL RUN

BOTTOM OF FIREPLACE

Summary of Contents for DLCX36SP93N-1





















































Reviews:

No comments