Page 2
R-3451
Introduction
Always consult your local Building Department regarding regulations,
codes or ordinances which apply to the installation of an unvented room
heater.
This appliance may be installed in an aftermarket* permanently located,
manufactured (mobile) home, where not prohibited by state or local
codes.
*Aftermarket: Completion of sale, not for purpose of resale, from the
manufacturer.
This appliance is only for use with the type of gas indicated on the rating
plate.
Instructions to Installer
1.
Installer must leave instruction manual with owner after installa-
tion.
2.
Installer must have owner fill out and mail warranty card supplied
with unvented room heater.
3.
Installer should show owner how to start and operate unvented
room heater.
WARNING: ANY CHANGE TO THIS HEATER OR ITS CON-
TROLS CAN BE DANGEROUS.
Any safety screen or guard removed for servicing an appliance
must be replaced prior to operating the heater.
WARNING
More frequent cleaning may be required due to excessive lint
from carpeting, bedding materials, etc. It is imperative that
control compartments, burners and circulating air passageways
of the appliance be kept clean.
•
DO make a periodic visual check of pilot and burners. Clean and
replace damaged parts.
•
DO NOT use this room heater if any part has been under water.
Immediately call a qualified service technician to inspect the
room heater and to replace any part of the control system and
any gas control which has been under water.
•
Due to high surface temperatures, keep children, clothing and
furniture away.
•
Under no circumstances should any solid fuels (wood, coal, paper
or cardboard etc.) be used in this appliance.
•
The flow of combustion and ventilation air must not be obstructed
in any way.
•
An unvented room heater having an input rating of more than
10,000 Btu per hour shall not be installed in a bedroom or
bathroom.
•
Due to high temperatures, the appliance should be located out
of traffic and away from furniture and draperies.
•
Children and adults should be alerted to the hazard of high
surface temperature and should stay away to avoid burns or
clothing ignition.
•
Young children should be carefully supervised when they are
in the same room with the appliance.
•
Do not place clothing or other flammable material on or near
the appliance.
•
Keep burner and control compartment clean.
•
Installation and repair should be done by a QUALIFIED
SERVICE PERSON. The appliance should be inspected before
use and at least annually by a professional service person.
THIS IS A HEATING APPLIANCE
DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.
When used without adequate combustion and ventilation air,
heater may give off CARBON MONOXIDE, an odorless, poison-
ous gas.
Do not install heater until all necessary provisions are made
for combustion and ventilation air. Consult the written in-
structions provided with the heater for information concern-
ing combustion and ventilation air. In the absence of instruc-
tions, refer to the National Fuel Gas Code, ANSI Z223.1,
Section 5.3 or applicable local codes.
This heater is equipped with a PILOT LIGHT SAFETY SYS-
TEM designed to turn off the heater if not enough fresh air is
available.
DO NOT TAMPER WITH PILOT LIGHT SAFETY
SYSTEM!
If heater shuts off, do not relight until you provide fresh air.
If heater keeps shutting off, have it serviced. Keep burner and
control compartment clean.
CARBON MONOXIDE POISONING MAY LEAD TO
DEATH.
Early signs of carbon monoxide poisoning resemble the flu, with
headache, dizziness and/or nausea. If you have these signs, heater
may not be working properly. Get fresh air at once! Have heater
serviced.
Some people — pregnant women, persons with heart or lung
disease, anemia, those under the influence of alcohol , those at high
altitudes — are more affected by carbon monoxide than others.
The pilot light safety system senses the depletion of oxygen at its
location. If this heater is installed in a structure having a high
vertical dimension, the possibility exists that the oxygen supply at
the higher levels will be less than that at the heater. In this type of
application, a fan to circulate the structure air will minimize this
effect. The use of this fan will also improve the comfort level in the
structure. When a fan is used to circulate air, it should be located
so that the air flow is not directed at the burner.
General Information
This CIVF-25 is design certified in accordance with American National
Standards Institute Z21.11.2b-1998 by the American Gas Associaton as
an Unvented Room Heater and should be installed according to these
instructions.
Attention: During initial use of ceramic log you will detect an odor
as the ceramic log is cured. Also, during the curing process the
ceramic log will burn with a yellow flame.
Any alteration of the original design, installed other than as shown
in these instructions or use with a type of gas not shown on the rating
plate is the responsibility of the person and company making the
change.
Important
All correspondence should refer to complete Model No., Serial No. and
type of gas.
Notice: During initial firing of this unit, its paint will bake out, and
smoke will occur. To prevent triggering of smoke alarms, ventilate the
room in which the unit is installed.
Summary of Contents for CIVF-25-2
Page 5: ...Page 5 R 3451 Figure 1 Figure 2 Figure 3 ...
Page 18: ...Page 18 R 3451 ...
