background image

Page 14

XPA-1L

Speaker Output Connections:

Audiophile grade five-way binding posts, gold plated with clear insulator, 1 pair.

Power Supply:

90,000 uF of storage capacitance.

 

450 VA heavy duty toroidal transformer.

Input Sensitivity (for rated power; 8 Ohm load):

1800 mV.

Gain:

29 dB.

Input Connections:

Unbalanced (RCA); balanced (XLR); switchable.

Input Impedance:

50k ohms.

Trigger:

Trigger Input: 5 - 20 V (AC or DC); <10 mA input current required.

 

Trigger Output: 12 VDC; can drive any load up to 100 mA.

Power Requirements:

115 VAC or 230 VAC +/- 10% @ 50 / 60 Hz (automatically detected and switched).

Front Panel Controls and Indicators:

Standby; push button (halo ring changes color to indicate Standby or On).

 

Status LED; illuminates blue for normal operation, flashes red during power-up or when a 

fault occurs (may be disabled by rear panel Status LED switch).

Rear Panel Controls:

AC Power switch; rocker switch (switches AC mains power).

 

Status LED switch; small slide switch (disables front panel Status LED).

 

Input selector; toggle switch (selects between balanced and unbalanced inputs).

Summary of Contents for XPA-1L



























Reviews: